The effect of geometric structure on stiffness and damping factor of wood applicable to machine tool structure

Susilo Adi Widyanto, Achmad Widodo, Sri Nugroho, David Siahaan


DOI: https://doi.org/10.12777/ijse.4.2.57-60

Abstract


Stiffness and vibration damping capability are important criteria in design of machine tool structure. In other sides, the weight of machine tool structure must be reduced to increase  the handling capability. This paper presents  an analysis of the effect of geometric structure on stiffness and vibration damping of wood structure.  The stiffness was analysed  using numerical method, so called finite element method (FEM), while the vibration damping capability was experimentally tested. Vibration testing was also performed to wood structures with sand powder filled  into  its rectangular hole to observe the its effect on damping factor. Simulation results show  that the cross ribs structure yielded minimum mass reduction ratio compared to the three square holes as well as the single rectangular hole structures. While the vibration test results explained that the damping factor of Shorea laevis wood was higher than that Hevea braziiensis wood. The use of sand powder as vibrating  mass in closed-box structure effectively increased the damping capability, for single rectangular hole structure the damping factor was increased from 0.048 to 0.079

doi: http://dx.doi.org/10.12777/ijse.4.2.2013.57-60

[How to cite the article: Widyanto, S. A., Widodo, A., Nugroho, S., & Siahaan, D. (2013). The effect of geometric structure on stiffness and damping factor of wood applicable to machine tool structure. INTERNATIONAL JOURNAL OF SCIENCE AND ENGINEERING, 4(2), 57-60. doi: http://dx.doi.org/10.12777/ijse.4.2.2013.57-60]


Keywords


Shorea laevis, Hevea braziiensis; stiffness; damping factor; machine tool structure

Full Text:

PDF

References


Buccur, V. (2006). Acoustics of wood 2nd ed, SPRIN-GER VERLAG

Ciornei, M., Diaconescu, E., and Glovnea, M. (2009). Experimental Invertigations of Wood Damping and Elastic Modulus. DOCT-US, 1(1): 56-61

Harms, A. (2006). Increasing the dynamic stiffness of Machine tools by means of Modal Analysis. in PROCEEDING MACHINE TOOL CONSTRUCTION CONFERENCE 23th March 2006, Munich, Germany

Hossein, M.A., Shahverdi, M., and Roohnia. (2011). The Effect of Wood Knot as a Defect on Modulus of Elasticity (MOE) and Damping Correlation. NOTE SCI BIOL, 3(3): 145-149

Koci, P. (2003). Assessment of machine tool dynamic properties. ACTA MONTANISTICA SLOVACA, 8(4): 179-181

Lee, D. G., Suh, J. G., Kim, H. S., and Kim, J. M. (2003). Design and manufacture of composite high speed machine tool structures. COMPOSITES SCIENCE AND TECHNOLOGY, 64: 1523–1530. http://dx.doi.org/10.1016/j.compscitech.2003.10.021

Nakaminami, M., Tokuma, T., Matsumoto, K., Sakashita, S., Moriwaki, T., and Nakamoto, K. (2007). Optimal Structure Design Methodology for Compound Multiaxis Machine Tools. INTERNATIONAL JOURNAL OF AUTOMATION TECHNOLOGY, 1(2): 87

Ouis, Q. (2002). On the frequency dependence of the modulus of elasticity of wood. WOOD SCIENCE AND TECHNOLOGY, 36(4): 335–346. http://dx.doi.org/10.1007/s00226-002-0145-5

Slocum, A. H., Marsh, E. R., and Smith, D. H. (1994). A new damper design for machine tool structures: the replicated internal viscous damper, PRECISION ENGINEERING, 16(3): 174-183. http://dx.doi.org/10.1016/0141-6359(94)90122-8

Wakasawa, Y., Hashimoto, M., and Marui, E. (2004). The damping capacity improvement of machine tool structures by balls packing. INTERNATIONAL JOURNAL OF MACHINE TOOLS AND M ANUFACTURE, 44: 1527-1536. http://dx.doi.org/10.1016/j.ijmachtools.2004.05.001




Published by Department of Chemical Engineering University of Diponegoro Semarang
Google Scholar

IJSE  by http://ejournal.undip.ac.id/index.php/ijse is licensed under Creative Commons Attribution 3.0 License.