DOI: https://doi.org/10.14710/teknik.v43i3.48653

Analysis of Ankle Foot Design for Transtibial Prosthesis Components using the Finite Element Method

*Wahyu Dwi Lestari orcid scopus  -  Department of Mechanical Engineering, Faculty of Engineering, University of Pembangunan Nasional "Veteran" Jawa Timur, Indonesia
Ndaru Adyono  -  Department of Mechanical Engineering, Faculty of Engineering, University of Pembangunan Nasional Veteran Jawa Timur
Open Access Copyright (c) 2022 TEKNIK

Citation Format:
Abstract

Finite element method (FEM) has been identified as a tool that can be used to analyze stress and strain behavior occurring in prosthetic components of the lower extremities. The main objective of this study was to analyze the structure of the alternative ankle foot designed for the transtibial prosthesis component. The ankle foot is designed and simulated for strength using Solidworks software. There are two alternative designs of the ankle foot that are designed. The material used is AISI 304 with Young's Modulus 193000 MPa and Poisson's Ratio 0.29. Based on the design results, the lowest weight is owned by alternative design 1 of 491.69 grams. The simulation was carried out under normal running conditions in the midstance phase. The applied load is 1000N. There are three data obtained from the simulation results in the form of von Mises stress, deformation, and strain energy. Based on the simulation results on alternative ankle foot design 2, the value of von Misses stress is lower. Even so, the two alternative designs that have been designed are still within safe limits because they still meet the predetermined safety factor value.

 

Fulltext View|Download
Keywords: Ankle Foot; Transtibial Prosthesis; AISI 304; Midstance; FEM
Funding: LPPM Universitas Pembangunan Nasional Veteran Jawa Timur

Article Metrics:

Article Info
Section: Artikel
Language : EN
Recent articles
Pengaruh Variasi Arah Medan Magnet Pembakaran Premixed Minyak Nabati terhadap Karakteristik Nyala Api pada Tungku Industri Autonomous Car Mechanical Performance Analysis with Region of Interest Method Using Raspberry Pi 4 and Arduino Nano Synthesis and Performance Evaluation of Magnetized Modified Coal Fly Ash as Adsorbent for Naphthol Blue Black Dye Removal from Synthetic Dye Wastewater Front Matter Back Matter More recent articles
Most cited articles
PENURUNAN MODEL PERMUKAAN DIJITAL (DSM) MENJADI MODEL ELEVASI DIJITAL (DEM) DARI CITRA SATELIT ALOS PALSAR (Studi kasus: NAD Bagian Tenggara, Indonesia) KORELASI PENURUNAN MUKA TANAH DENGAN PENURUNAN MUKA AIR TANAH DI KOTA SEMARANG PERMASALAHAN AIRTANAH PADA DAERAH URBAN PERBANDINGAN NILAI KALOR BIOBRIKET YANG TERBUAT DARI BOTTOM ASH LIMBAH PLTU DAN BIOMASSA CANGKANG KOPI DENGAN VARIASI KOMPOSISI DAN JENIS PENGIKAT YANG BERBEDA PENGGUNAAN ABU SEKAM PADI SEBAGAI ADSORBEN DALAM PENGOLAHAN AIR LIMBAH YANG MENGANDUNG LOGAM Cu More cited articles
  1. Bateni, Hamid, and Sandra J. Olney. n.d. “Effect of the Weight of Prosthetic Components on the Gait of Transtibial Amputees.” 45–47
  2. Chow, Daniel H. K., Andrew D. Holmes, Christina K. L. Lee, and S. W. Sin. 2006. “The Effect of Prosthesis Alignment on the Symmetry of Gait in Subjects with Unilateral Transtibial Amputation.” Prosthetics and Orthotics International 30(2):114–28. doi: 10.1080/03093640600568617
  3. Fridman, A., I. Ona, and E. Isakov. 2003. “The Influence of Prosthetic Foot Alignment on Trans-Tibia1 Amputee Gait.” 17–22
  4. Gard, Steven A. 2006. “Use of Quantitative Gait Analysis for the Evaluation of Prosthetic Walking Performance.” Journal of Prosthetics and Orthotics 18(6 PROCEEDINGS). doi: 10.1097/00008526-200601001-00011
  5. Geil, Mark D., and A. Lay. 2004. “Plantar Foot Pressure Responses to Changes during Dynamic Trans-Tibial Prosthetic Alignment in a Clinical Setting.” Prosthetics and Orthotics International 28(2):105–14. doi: 10.1080/03093640408726695
  6. Hsu, Miao-ju, David H. Nielsen, H. Yack, and Donald G. Shurr. n.d. “Physiological Measurements of Walking and Running in People With Transtibial Amputations With 3 Different Prostheses.” 29(9):526–33
  7. International, Orthotics, and Central Military Hospital. 1984. “Biomechanical Significance of the Correct Length of Lower Limb Prostheses : A Clinical and Radiological Study .” (1983):124–29
  8. Ismawan, Ade Reza, Rifky Ismail, Tony Prahasto, Mochammad Ariyanto, and Budi Setiyana. 2022. “A Review of Existing Transtibial Bionic Prosthesis: Mechanical Design, Actuators and Power Transmission.” Journal of Biomedical Science and Bioengineering 1(2):65–72. doi: 10.14710/jbiomes.2021.v1i2.65-72
  9. Jia, Xiaohong, Xiaobing Li, Peng Dou, and Ming Zhang. 2005. “The Influence of Dynamic Trans-Tibial Prosthetic Alignment on Standing Plantar Foot Pressure.” Annual International Conference of the IEEE Engineering in Medicine and Biology - Proceedings 7 VOLS:6916–18. doi: 10.1109/iembs.2005.1616096
  10. Jia, Xiaohong, Ming Zhang, and Winson C. C. Lee. 2004. “Load Transfer Mechanics between Trans-Tibial Prosthetic Socket and Residual Limb — Dynamic Effects.” 37:1371–77. doi: 10.1016/j.jbiomech.2003.12.024
  11. Kang, P., J. H. Kim, and J. S. Roh. 2006. “Pressure Distribution in Stump/Socket Interface in Response to Socket Flexion Angle Changes in Trans-Tibial Prostheses with Silicone Liner.” Physical Therapy Korea 13(4):71–78
  12. Lee, Raymond Y., and Alan Turner-Smith. 2003. “The Influence of the Length of Lower-Limb Prosthesis on Spinal Kinematics.” Archives of Physical Medicine and Rehabilitation 84(9):1357–62. doi: 10.1016/S0003-9993(03)00259-4
  13. Lee, Winson C. C., Ming Zhang, Xiaohong Jia, and Jason T. M. Cheung. 2004. “Finite Element Modeling of the Contact Interface between Trans-Tibial Residual Limb and Prosthetic Socket.” Journal of Rehabilitation Research and Development 26:655–62. doi: 10.1016/j.medengphy.2004.04.010
  14. Leung, Aaron K. L., and Winson C. C. Lee. 2012. “Prosthetics and Orthotics.” Orthopaedic Biomechanics 583–602. doi: 10.1201/b13733
  15. Orthopaedics, Clinical, Leslie Torburn, and Josh Perry. 2017. “Below-Knee Amputee Gait in Stair Ambulation.” (January)
  16. Pasquina, P.F., Bryant, P.R., Huang, M.E., Roberts, T.L., Nelson, V.S., Flood, K. M. 2006. “Advances in Amputee Care.” Arch. Phys. Med. Rehabil. 87(March):34–43. doi: 10.1016/j.apmr.2005.11.026
  17. Saunders, Marnie M., Edwards P. Schwentker, David B. Kay, Gordon Bennett, Christopher R. Jacobs, Mary C. Verstraete, and Glen O. Njus. 2003. “Finite Element Analysis as a Tool for Parametric Prosthetic Foot Design and Evaluation. Technique Development in the Solid Ankle Cushioned Heel (SACH) Foot.” Computer Methods in Biomechanics and Biomedical Engineering 6(1):75–87. doi: 10.1080/1025584021000048974
  18. Turcot, Katia, Sagawa Jr, Alain Lacraz, Jean Lenoir, and Mathieu Assal. 2013. “Comparison of the International Committee of the Red Cross Foot With the Solid Ankle Cushion Heel Foot During Gait : A Randomized Double-Blind Study.” 1490–97. doi: 10.1016/j.apmr.2013.03.019
  19. Underwood, Heather A., Craig D. Tokuno, and Janice J. Eng. 2012. “A Comparison of Two Prosthetic Feet on the Multi-Joint and Multi- Plane Kinetic Gait Compensations in Individuals with a Unilateral Trans-Tibial Amputation.” Clin Biomech 19(6):609–16. doi: 10.1016/j.clinbiomech.2004.02.005.A
  20. Xiaobing, Li, Jia Xiaohong, Dou Peng, and Fang Lidan. 2005. “Influence of Shoe-Heel Height of the Trans-Tibial Prosthesis on Static Standing Biomechanics.” 5227–29
  21. Zhang M, Lord M, Turner-Smith AR, Roberts VC. 1995. “Development of a Non-Linear Modelling of the below-Knee Interface Finite Element Prosthetic Socket.” Medical Engineering and Physics 17:559–66
  22. Zhang, Ming, Arthur F. T. Mak, and V. C. Roberts. 1998. “Finite Element Modelling of a Residual Lower-Limb in a Prosthetic Socket: A Survey of the Development in the First Decade.” Medical Engineering and Physics 20(5):360–73. doi: 10.1016/S1350-4533(98)00027-7

Last update:

No citation recorded.

Last update: 2024-11-21 10:10:29

No citation recorded.