Vulcanization Kinetics and Mechanical Properties of Ethylene Propylene Diene Monomer Thermal Insulation

DOI: https://doi.org/10.9767/bcrec.10.2.6682.104-110
Cover Image

Article Metrics: (Click on the Metric tab below to see the detail)

Article Info
Submitted: 08-04-2014
Published: 12-07-2015
Section: Original Research Articles
Fulltext PDF Tell your colleagues Email the author
The vulcanization kinetics of Ethylene-propylene diene monomer (EPDM) rubber thermal insulation was studied by using rheometer under isothermal condition at different temperatures. The rheometry analysis was used to determining the cure kinetic parameters and predicting the cure time of EPDM thermal insulation. The experimental results revealed that the curing curves of EPDM thermal insulation were marching and the optimum curing time decreased with increasing the temperature. The kinetic parameters were determined from the autocatalytic model showed close fitting with the experimental results, indicating suitability of autocatalytic model in characterizing the cure kinetics. The activation energy was determined from the autocatalytic model is 46.3661 kJ mol-1. The cure time were predicted from autocatalytic model and the obtained kinetic parameter by using the relationship among degree of conversion, cure temperature, and cure time. The predictions of cure time provide information for the actual curing characteristic of EPDM thermal insulation. The mechanical properties of EPDM thermal insulation with different vulcanization temperatures showed the same hardness, tensile strength and modulus at 300%, except at temperature 70 °C, while the elongation at breaking point decreased with increasing temperature of vulcanization. © 2015 BCREC UNDIP. All rights reserved

Received: 8th April 2014; Revised: 7th January 2015; Accepted: 16th January 2015

How to Cite: Fathurrohman, M.I., Maspanger, D.R., Sutrisno, S. (2015). Vulcanization Kinetics and Mechanical Properties of Ethylene Propylene Diene Monomer Thermal Insulation. Bulletin of Chemi-cal Reaction Engineering & Catalysis, 10 (2), 104-110. (doi:10.9767/bcrec.10.2.6682.104-110)

Permalink/DOI: http://dx.doi.org/10.9767/bcrec.10.2.6682.104-110

 

Keywords

Vulcanization kinetics; EPDM; thermal insulation; autocatalytic model

  1. Mohamad Irfan Fathurrohman 
    Indonesian Rubber Research Institute, Jl.Salak no.1 Bogor 16151,, Indonesia
  2. Dadi Rusadi Maspanger 
    Indonesian Rubber Research Institute, Jl.Salak no.1 Bogor 16151,, Indonesia
  3. Sutrisno Sutrisno 
    Rocket Technology Center, National Institute of Aeronautics and Space, Jl. Raya LAPAN No. 2, Mekarsari, Rumpin, Bogor 16350, Indonesia
  1. Bhuvaneswari, C.M., Sureshkumar, M.S., Kakade, S.D., Gupta Manoj. (2006). Ethylene-Propylene Diene Rubber as a Futuristic Elastomer for Insulation of Solid Rocket Motors. Defence Science Journal, 56(30): 309-320.
  2. Sae-oui, P., Thepsuwan, U. (2002). Prediction of Cure Level in Thick Rubber Cylinder using Finite Element Analysis. Science Asia, 28: 385-391.
  3. Karaagac, B., Inal, M., Deniz, V. (2009). Artificial Neural Network Approach for Predicting Optimum Cure Time of Rubber Compound. Materials and Design, 30: 1685-1690.
  4. Karaagac, B., Inal, M., Deniz, V. (2012). Predicting Optimum Cure Time of Rubber by Means of ANFIS. Materials and Design, 35: 833-838.
  5. Leroy, E., Souid, A., Deterre, R. (2013). A Continuous Kinetic Model of Rubber Vulcanization Predicting Induction and Reversion. Polymer Testing, 32(3): 575-582.
  6. Leroy, E., Souid, A., Sarda, A., Deterre, R. (2013). A Knowledge Based Approach for Elastomer Cure Kinetic Parameters Estimation. Polymer Testing, 32(1): 9-14.
  7. Ghosh, P., Katare, S., Patkar, P., Caruthers, J.M., Venkatasubramanian, V. (2003). Sulfur Vulcanization of Natural Rubber for Ben-zothiazole Accelerated Formulations: From Reaction Mechanisms to a Rotational Kinetic Model. Rubber Chemistry Technology, 76 (3): 592-693.
  8. Zaimova, D., Bayraktar, E., Dishovsky, N. (2011). State of Cure Evaluation by Different Experiment Methods in Thick Rubber Parts. Journal of Achievements in Materials and Manufacturing Engineering, 44(2): 161-167.
  9. Rosca, I.D., Vergnaud, J.M. (2001). Study of Process of Cure of EPDM Rubbers in Moving Die Rheometer. Plastics, Rubber and Composites, 30 (6): 275-281.
  10. Hasan, A., Rochmadi., Hary, S., Suharto, H. (2012). The Effect of Rubber Mixing Process on The Curing Characteristics of Natural Rubber. Makara Teknologi, 16 (2): 109-115.
  11. Gonzalez, L., Rodriguez, A., Valentin, J.L., Marcos-Fernandez, A., Posadas, P. (2005). Conventional and Efficient Crosslinking of Natural Rubber. Kautsch. GummiKunstst, 58: 638-643.
  12. Choi, D., Kader, M, A., Cho, B.H., Huh, Y., Nah, C. (2005). Vulcanization Kinetics of Nitrile Rubber/Layered Clay Nanocomposites. Journal of Applied Polymer Science, 98: 1688-1696.
  13. Sui, G., Zhong, W.H., Yang, X.P., Yu, Y.H. (2008). Curing kinetics and Mechanical Behavior of Natural Rubber Reinforced with Pretreated Carbon Nanotubes. Materials Science and Engineering A, 485: 524-531.
  14. Franck, A., Hafner, K., Kern, W.F. (1962). The Activation Energy of Vulcanization. Rubber Chemistry and Technology, 35(1): 76-91.
  15. Bhuvaneswari, C.M., Kakade, S.D., Deuskar, V.D., Dange, A.B., Gupta, M. (2008). Filled Ethylene-Propylene Diene Terpolymer Elastomer as Thermal Insulator for Case-Bonded Solid Rocket Motors. Defence Science Journal, 58(1): 94-102.
  16. NASA, (1971). Solid Propellant Processing Factors in Rocket Motor Design.Monograph NASA SP-8075 : 28
  17. Sutrisno, S., Chawari, M, (1994). HTPB Propellant Processing Based on Fuel/Curing Agent Ratio, LAPAN, XVIII No.69: 36-38.
  18. Ahmed, K., Nizami, S.S., Raza, N.Z., Shirin, K. (2012). Cure Characteristics, Mechanical and Swelling Properties of Marble Sludge Filled EPDM Modified Chloroprene Rubber Blends. Advances in Material Physics and Chemistry, 2: 90-97.