PENGARUH  JENIS ANODA PADA PROSES PEMULIHAN  LOGAM NIKEL  DARI TIRUAN AIR LIMBAH ELECTROPLATING MENGGUNAKAN SEL ELEKTRODEPOSISI

Djaenudin Dhaenudin; Mindriany Syafila; Edwan Kardena; Isdiriayani Nurdin

doi:10.14710/reaktor.14.3.211-217

DOI: https://doi.org/10.14710/reaktor.14.3.211-217

PENGARUH JENIS ANODA PADA PROSES PEMULIHAN LOGAM NIKEL DARI TIRUAN AIR LIMBAH ELECTROPLATING MENGGUNAKAN SEL ELEKTRODEPOSISI

*Djaenudin Dhaenudin - Program Studi Doktor Teknik Lingkungan, Fakultas Teknik Sipil dan Lingkungan, , Indonesia

Mindriany Syafila - Program Studi Doktor Teknik Lingkungan, Fakultas Teknik Sipil dan Lingkungan, , Indonesia

Edwan Kardena - Program Studi Doktor Teknik Lingkungan, Fakultas Teknik Sipil dan Lingkungan, , Indonesia

Isdiriayani Nurdin - Program Studi Doktor Teknik Lingkungan, Fakultas Teknik Sipil dan Lingkungan, , Indonesia

Published: 3 Mar 2013.

BibTex Citation Data :

@article{Reaktor6098,
    author = {Djaenudin Dhaenudin and Mindriany Syafila and Edwan Kardena and Isdiriayani Nurdin},
    title = {PENGARUH  JENIS ANODA PADA PROSES PEMULIHAN  LOGAM NIKEL  DARI TIRUAN AIR LIMBAH ELECTROPLATING MENGGUNAKAN SEL ELEKTRODEPOSISI},
    journal = {Reaktor},
  volume = {14},
    number = {3},
    year = {2013},
    keywords = {anoda; elektrodeposisi; grafit; timbal; pemulihan nikel; stainless steel tipe AISI 316},
    abstract = { EFFECT OF ANODES TYPES ON NICKEL RECOVERY FROM SYNTHETIC ELECTROPLATING WASTE ELECTRODEPOSITION CELLS.  A study concerning the   recovery of nickel from electroplating wastewater artificial solution. The study was conducted with a batch system using electrodeposition cell consisting of two spaces separated by water hyacinth lea  f  , copper cathode plate, H 2 SO 4  solution anolyte, catholyte solution of NiSO 4  plus NaCl supporting electrolyte and anode varied. Electrodeposition performed at   the direct current     of   5V power for 4 hours each   run  . The research objective   was     to obtain   the best anode in nickel electrodeposition process of electroplating waste artificial solution. Graphite, stainless   s  teel   type AISI 316 and the lead   were   used   as a variation of the anode. Concentration of nickel in the catholyte at baseline 2200 mg  /  L.   The results showed that the anode   was   a   graphite anode with best value decreased by 72.44% nickel concentration, deposition of nickel on the cathode of 0.188 grams and specific energy values of 6.1625 k  Wh  /kg.nickel  .          Telah dilakukan penelitian tentang pemulihan logam nikel dari larutan tiruan air limbah electroplating. Penelitian dilakukan dengan sistem batch menggunakan sel elektrodeposisi yang terdiri dari dua ruang yang dipisahkan dengan daun eceng gondok, katoda pelat tembaga, anolit larutan H 2 SO 4 , katolit larutan NiSO 4  ditambah elektrolit pendukung larutan NaCl dan anoda divariasikan. Elektrodeposisi dilakukan pada listrik searah sebesar 5V selama 4 jam setiap tempuhan. Tujuan penelitian adalah memperoleh anoda terbaik pada proses elektrodeposisi nikel dari larutan tiruan limbah electroplating. Grafit, Stainless Steel  tipe AISI 316 dan timbal digunakan sebagai variasi jenis anoda. Konsentrasi nikel dalam katolit pada awal penelitian 2200 mg/L. Hasil penelitian menunjukkan bahwa anoda grafit merupakan anoda yang paling baik dengan nilai penurunan konsentrasi nikel sebesar 72,44%, deposisi nikel di katoda sebesar 0,188 gram dan nilai energi spesifik sebesar 6,1625  kWh/kg.nikel.  },
   issn = {2407-5973},   pages = {211--217}  doi = {10.14710/reaktor.14.3.211-217},
    url = {https://ejournal.undip.ac.id/index.php/reaktor/article/view/6098}
}

Citation Format:

Abstract

EFFECT OF ANODES TYPES ON NICKEL RECOVERY FROM SYNTHETIC ELECTROPLATING WASTE ELECTRODEPOSITION CELLS. A study concerning the recovery of nickel from electroplating wastewater artificial solution. The study was conducted with a batch system using electrodeposition cell consisting of two spaces separated by water hyacinth leaf, copper cathode plate, H₂SO₄ solution anolyte, catholyte solution of NiSO₄ plus NaCl supporting electrolyte and anode varied. Electrodeposition performed at the direct current of 5V power for 4 hours each run. The research objective was to obtain the best anode in nickel electrodeposition process of electroplating waste artificial solution. Graphite, stainless steel type AISI 316 and the lead were used as a variation of the anode. Concentration of nickel in the catholyte at baseline 2200 mg/L. The results showed that the anode was a graphite anode with best value decreased by 72.44% nickel concentration, deposition of nickel on the cathode of 0.188 grams and specific energy values of 6.1625 kWh/kg.nickel.

Telah dilakukan penelitian tentang pemulihan logam nikel dari larutan tiruan air limbah electroplating. Penelitian dilakukan dengan sistem batch menggunakan sel elektrodeposisi yang terdiri dari dua ruang yang dipisahkan dengan daun eceng gondok, katoda pelat tembaga, anolit larutan H₂SO₄, katolit larutan NiSO₄ ditambah elektrolit pendukung larutan NaCl dan anoda divariasikan. Elektrodeposisi dilakukan pada listrik searah sebesar 5V selama 4 jam setiap tempuhan. Tujuan penelitian adalah memperoleh anoda terbaik pada proses elektrodeposisi nikel dari larutan tiruan limbah electroplating. Grafit, Stainless Steel tipe AISI 316 dan timbal digunakan sebagai variasi jenis anoda. Konsentrasi nikel dalam katolit pada awal penelitian 2200 mg/L. Hasil penelitian menunjukkan bahwa anoda grafit merupakan anoda yang paling baik dengan nilai penurunan konsentrasi nikel sebesar 72,44%, deposisi nikel di katoda sebesar 0,188 gram dan nilai energi spesifik sebesar 6,1625 kWh/kg.nikel.

Fulltext View|Download

Keywords: anoda; elektrodeposisi; grafit; timbal; pemulihan nikel; stainless steel tipe AISI 316

Article Metrics:

Article Info

Section: Research Article

Language : EN

In Volume 14, No. 3, APRIL 2013

Recent articles

PADDY DRYING IN MIXED ADSORPTION DRYER WITH ZEOLITE: DRYING RATE AND TIME ESTIMATION PENJERAPAN GAS CO HASIL PEMBAKARAN SAMPAH MENGGUNAKAN SORBENT TERMODIFIKASI DALAM REAKTOR FIXED BED UPAYA PENINGKATAN MUTU DAN EFISIENSI PROSES PENGERINGAN JAGUNG DENGAN MIXED-ADSORPTION DRYER More recent articles

Most cited articles

UTILIZATION OF PINEAPPLE WASTE AS CARBON SOURCE Synthesis of Matrix Si-K-HAs Gel from Geothermal Sludge and Peat Influence of Microwave Irradiation on Extraction of Chitosan from Shrimp Shell Waste Optimization of Xylose Production from Sugarcane Trash by Microwave-Maleic Acid Hydrolysis PREPARATION AND CHARACTERIZATION OF SULFATED ZIRCONIA FOR BIODIESEL PRODUCTION More cited articles

Last update:

Effect of Electrolyte Composition on Nickel Removal Process from Artificial Electroplating Wastewater Using Two-Room Electrodeposition Cells
Selly Ayu Janetasari, Djaenudin Djaenudin. Jurnal Kimia Sains dan Aplikasi, 22 (4), 2019. doi: 10.14710/jksa.22.4.143-149

Last update: 2025-01-20 23:12:52

No citation recorded.

In order for REAKTOR to publish and disseminate research articles, we need non-exclusive publishing rights (transferred from the author(s) to the publisher). This is determined by a publishing agreement between the Author(s) and REAKTOR. This agreement deals with transferring or licensing the publishing copyright to REAKTOR while Authors still retain significant rights to use and share their published articles. REAKTOR supports the need for authors to share, disseminate, and maximize the impact of their research and these rights in any databases.

As a journal author, you have the right to use your article for many purposes, including by your employing institute or company. These Author rights can be exercised without the need to obtain specific permission. Authors publishing in BCREC journals have wide rights to use their works for teaching and scholarly purposes without needing to seek permission, including, but not limited to:

use for classroom teaching by the Author or the Author's institution and presentation at a meeting or conference and distributing copies to attendees;
use for internal training by the author's company;
distribution to colleagues for their research use;
use in a subsequent compilation of the author's works;
inclusion in a thesis or dissertation;
reuse of portions or extracts from the article in other works (with full acknowledgment of the final article);
preparation of derivative works (other than commercial purposes) (with full acknowledgment of the final article);
voluntary posting on open websites operated by the author or the author’s institution for scholarly purposes,

(but it should follow the open access license of Creative Common CC-by-SA License).

Authors/Readers/Third Parties can copy and redistribute the material in any medium or format and remix, transform, and build upon the material for any purpose, even commercially. Still, they must give appropriate credit (the name of the creator and attribution parties (authors detail information), a copyright notice, an open access license notice, a disclaimer notice, and a link to the material), provide a link to the license, and indicate if changes were made (Publisher indicates the modification of the material (if any).

Authors/Readers/Third Parties can read, print and download, redistribute or republish the article (e.g., display in a repository), translate the article, download for text and data mining purposes, reuse portions or extracts from the article in other works, sell or re-use for commercial purposes, remix, transform, or build upon the material, they must distribute their contributions under the same license as the original Creative Commons Attribution-ShareAlike (CC BY-SA).