DOI: https://doi.org/10.14710/teknik.v41i1.26125

Sealing Performance Layered Metal Gasket Based on the Simulation Method

*I Made Gatot Karohika orcid scopus  -  Program Studi Teknik Mesin, Universitas Udayana, Indonesia
Shigeyuki Haruyama  -  Graduate School of Innovation and Technology Management, Yamaguchi University, Japan
I Nyoman Gde Antara  -  Program Studi Teknik Mesin, Universitas Udayana, Indonesia
I Nyoman Budiarsa  -  Program Studi Teknik Mesin, Universitas Udayana, Indonesia
I Made Dwi Budiana Penindra  -  Program Studi Teknik Mesin, Universitas Udayana, Indonesia
Open Access Copyright (c) 2020 TEKNIK

Citation Format:
Abstract

Studies for corrugated metal gaskets are still ongoing to improve its performance. This is considered to be a single gasket with SUS304 material when contact with flanges that have greater surface roughness, reduced contact width and plastic deformed contact surfaces are incomplete and cannot fill the surface roughness of flanged flanges. The use of softer material than the base material as a surface covering material is used to improve the performance of the gasket. In this study, therefore the effect of modulus of elasticity ratio and thickness ratio on contact width and contact stress, 25A three-layer metal gasket was investigated using Finite Element Analysis. The results showed that the material with tangent modulus, Ehal = Eal / 150 had the highest slope for contact width. While the contact width of the plastic mode gasket is higher than the elastic mode gasket.

Fulltext View|Download
Keywords: contact width, contact stress, layers, gaskets, corrugated, simulation
Funding: LPPM University of Udayana and Strength of Material laboratory, Yamaguchi University, Japan.

Article Metrics:

Article Info
Section: Artikel
Language : EN
Recent articles
Pemodelan Pupuk Rilis Lambat Dengan Fly Ash sebagai Matriks Inert yang Dilapisi oleh Ethylcellulose Redesain Awana Condotel Menggunakan Metode Flat slab Berdasarkan SNI 2847-2013 Analysis of Sinusoidal Pulse Width Modulation Parameter Settings in High Precission Closed Loop Full Bridge Bipolar Inverters for High Voltage High Frequency Generator Front Matter Erratum Back Matter More recent articles
Most cited articles
PENGARUH PEMBEBASAN LAHAN TERHADAP RISIKO PROYEK KONSTRUKSI (STUDI KASUS SOCIAL ENGINEERING PROYEK JALAN TOL RUAS SEMARANG BAWEN) PERMASALAHAN AIRTANAH PADA DAERAH URBAN PENGENALAN STABILISASI TANAH DENGAN JET GROUTING KONSEP WATERFRONT PADA PERMUKIMAN ETNIS KALI SEMARANG UNJUK KERJA REAKTOR PLASMA DIELECTRIC BARRIER DISCHARGE UNTUK PRODUKSI BIODIESEL DARI MINYAK KELAPA SAWIT More cited articles
  1. Choiron, M. A., Haruyama, S., & Kaminishi, K. (2012). Optimization of new metal gasket design based on contact width involving contact stress consideration. Applied Mechanics and Materials, 110–116(January), 4780–4787
  2. Choiron, M. A., Kurata, Y., Haruyama, S., & Kaminishi, K. (2011). Simulation and experimentation on the contact width of new metal gasket for asbestos substitution. International Journal of Aerospace and Mechanical Engineering, 5(4), 283-287
  3. Haruyama, S., Nurhadiyanto, D., Choiron, M. A., & Kaminishi, K. (2013). Influence of surface roughness on leakage of new metal gasket. International Journal of Pressure Vessels and Piping, 111, 146-154
  4. Karohika, I. M.G., & Antara, I. N. G. (2019a). Gasket Process Parameter in Metal Forming. IOP Conference Series: Earth and Environmental Science. 248(1), 012044
  5. Karohika, I. M.G., & Antara, I. N. G. (2019b). The metal gasket sealing performance of bolted flanged with fem analysis. IOP Conference Series: Materials Science and Engineering, 539(1), 012018
  6. Karohika, I. M.G., Antara, I. N. G., & Budiana, I. M. D. (2019). Influence of dies type for gasket forming shape. IOP Conference Series: Materials Science and Engineering. 539(1), 012019
  7. Karohika, I Made Gatot, & Antara, I. N. G. (2018). Proses Pembentukan Gasket berlapis dengan Metode Elemen Hingga. Jurnal Energi Dan Manufaktur, 11(2), 62-66
  8. Nurhadiyanto, D., Choiron, M. A., Kaminishi, K., & Haruyama, S. (2012). Optimization of New 25A-size Metal Gasket Design Based on Contact Width Considering Forming and Contact Stress Effect. International Journal of Mechanical and Mechatronics Engineering, 6(3), 671–675
  9. Nurhadiyanto, D., Haruyama, S., Kaminishi, K., Gatot Karohika, I. M., & Mujiyono, D. (2015). Contact Stress and Contact Width Analysis of Corrugated Metal Gasket. Applied Mechanics and Materials, 799–800, 765–769
  10. Saeed, H. A., Izumi, S., Sakai, S., Haruyama, S., Nagawa, M., & Noda, H. (2008). Development of New Metallic Gasket and its Optimum Design for Leakage Performance. Journal of Solid Mechanics and Materials Engineering, 2(1), 105-114

Last update:

  1. An overview of the corrugated metal gasket

    I. Made Gatot Karohika, I. Gusti Agung Gede Kusuma Artha, Muhammad Hadiyan Ari Ghilman Azkandri. THE 2ND INTERNATIONAL CONFERENCE ON DESIGN, ENERGY, MATERIALS AND MANUFACTURE 2021 (ICDEMM 2021), 2568 , 2023. doi: 10.1063/5.0115569

  2. Topology Optimization of Motorbike Footsteps Using Finite Element Method

    I Made Gatot Karohika, Januar Teguh Prasetyo, I Made Parwata, I Nyoman Gde Antara, I Nyoman Budiarsa. Engineering Innovations, 11 , 2024. doi: 10.4028/p-8EHMyY

  3. Development of airless tires: A review

    I. Made Gatot Karohika, Ananda Binawangsa, Frederick Frederick, Putu Dwi Dharma Eka Yasa, Kadek Rian Satria Raditya. THE 2ND INTERNATIONAL CONFERENCE ON DESIGN, ENERGY, MATERIALS AND MANUFACTURE 2021 (ICDEMM 2021), 2568 , 2023. doi: 10.1063/5.0115570

  4. Design of motorcycle footstep holder using topology optimization

    I. Made Gatot Karohika, I. Nyoman Gde Antara, Ainul Ghurri, Putu Dwi Dharma Eka Yasa, Kadek Rian Satria Raditya. FRONTIERS IN INDUSTRIAL AND APPLIED MATHEMATICS: FIAM2022, 3081 , 2024. doi: 10.1063/5.0199959

Last update: 2024-11-22 05:21:06

No citation recorded.