DOI: https://doi.org/10.14710/teknik.v41i3.27348

Study on Tool Deterioration in Machining with Minimum Quantity Lubrication (MQL) Condition

Kajian terhadap Tingkat Kerusakan Pahat pada Pembubutan dengan Metode Minimum Quantity Lubrication (MQL)

Rika Dwi Hidayatul Qoryah  -  Mechanical Engineering, Faculty of Engineering, Universitas Jember, Indonesia
Allen Luviandy  -  Mechanical Engineering, Faculty of Engineering, Universitas Jember, Indonesia
*Mahros Darsin scopus  -  Mechanical Engineering, Faculty of Engineering, Universitas Jember, Indonesia
Open Access Copyright (c) 2020 TEKNIK

Citation Format:
Abstract
This study aims to observe the tool deterioration following application of minimum quantity lubrication method (MQL). The designed MQL system is completed with an Arduino controller system which was able to be either manually-controlled or automatically-controlled. The tool used in this study is DCMT 11 insert type. The Taguchi method using the Orthogonal Array L9 design was used to compile the design of experiments with variations in depth of cut, coolant composition, and cooling fluid application methods. Each variable consists of three levels. Tool deterioration evaluated by observing it under an optic microscope from three sides of the tool. There are four levels of tool deterioration. The value of tool deterioration of each tool is the accumulation of each side view. ANOVA analysis found that depth of cut, cutting tool composition and method of applying coolant influence tool deterioration in percentage by 32.69%, 17.30 % and 12.82% respectively. Moreover, the minimum tool deterioration would be achieved when using the parameter combination of depth of cut of 1.6 mm; mixture composition of 3:7; and using the temperature-controlled MQL. 
Fulltext View|Download
Keywords: cutting fluid; MQL; Taguchi method; cutting tool; tool deterioration

Article Metrics:

Article Info
Section: Artikel
Language : EN
Recent articles
Analysis of Particulates and SO2 Removal from Coal Combustion Emissions Using Cyclone and Wet Scrubber With Textile Wastewater Feed The design of A Portable Fixed-Bed Composite Adsorber Column as a Biodiesel Purification Media with Packing Bed System Study on Tool Deterioration in Machining with Minimum Quantity Lubrication (MQL) Condition Back Matter Front Matter More recent articles
Most cited articles
ANALISIS RESIKO KONSENTRASI DEBU (TSP) DAN TIMBAL (Pb) DI PINGGIR JALAN TERHADAP KESEHATAN MANUSIA STUDI KASUS KOTA YOGYAKARTA TIPOLOGI DAN KONSEP INTEGRASI PADA LINGKUNGAN BANGUNAN PENDIDIKAN DENGAN KARAKTER ARSITEKTUR KOLONIAL DI JALAN KARTINI KOTA SALATIGA Flood Disaster Mitigation Using a Disaster Early Warning and Monitoring Information System with an IoT-Based Arduino Microcontroller PERSEPSI INTEGRASI TATA GUNA LAHAN PADA KAWASAN WATERFRONT DEVELOPMENT (Studi Kasus: Kanal Banjir Barat Semarang) PENGARUH PEMBEBASAN LAHAN TERHADAP RISIKO PROYEK KONSTRUKSI (STUDI KASUS SOCIAL ENGINEERING PROYEK JALAN TOL RUAS SEMARANG BAWEN) More cited articles
  1. Ali, S. M., Dhar, N. R., & Dey, S. K. (2011). Effect of minimum quantity lubrication (mql) on cutting performance in turning medium carbon steel by uncoated carbide insert at different speed-feed combinations. Advances in Production Engineering & Management, 6(3)
  2. Basuki, B. (2014). Pengaruh Metode Minimum Lubrication Keausan Pahat dan Kekasaran Permukaan Benda Kerja AISI 4340. Jurnal Teknologi, 7(2), 112-117
  3. Bayuseno, A. P. (2010). Kajian Pustaka Tentang Keausan Pahat Bubut. Rotasi , 12(2), 38-41
  4. Boubekri, N., & Shaikh, V. (2015). Minimum Quantity Lubrication (MQL) in Machining: Benefits and Drawback. Journal of Industrial and Intelligent Information, 3(3), 205-209
  5. Dalimunthe, R. (2009). Pengaruh Kecepatan Potong Terhadap Umur Pahat HSS Pada Proses Pembubutan AISI 4340. Jurnal Sains dan Inovasi, 5(2), 139-145
  6. Darsin, M., Pasang, T, & Chen, Z. (2017). Performance of TiAlN PVD Coated Carbide Drill when Drilling Titanium 6246 Alloy. MATEC Web of Conferences 109, 02001
  7. Dinata, G. G. S., Muttaqin, A. Z., & Darsin, M. (2020) Rancang bangun dan uji performa sistem kendali pemberian fluida permesinan MQL berbasis arduino. Rekayasa Mesin, 11(1), 97–104
  8. Ekinovic, S, H. Prcanovic, H., E. & Begovica, E. (2015). Investigation of influence of MQL machining parameters on cutting forces during MQL turning of carbon steel St52-3. The Manufacturing Engineering Society International Conference, MESIC 2015
  9. Gupta, M. K., Mia, M., Jamil, M., Singh, R. Singla, A. K. Song, Q., Liu, Z., Khan, A. M., Rahman, M. A., Sarikaya, M. (2020). Machinability investigations of hardened steel with biodegradable oil-based MQL spray system. The International Journal of Advanced Manufacturing Technology, 108,735–748
  10. Khanna, N., & Davim, J. P. (2015). Design of experiments application in machining titanium alloys for aerospace structural components. Measurement, 61, 280–290
  11. Patriawan, D. A., Irawan, H., & Widodo, E. W. R. (2016). Studi Pendahuluan Penggunaan Minimum Quantity Lubricant Pada Proses Pemesinan. Prosiding Seminar Nasional Sains dan Teknologi Terapan, 153-160
  12. Qomarudin & Rahmanto, R. H. (2018). Analisis Kekerasan dan Keausan Pahat Bubut HSS. Prosiding seminar nasional energi & teknologi (SINERGI) 2016, 47-50
  13. Rochim, T. (2007). Perkakas dan Sistem Pemerkakasan. Bandung: Penerbit ITB
  14. Shihab, S. K., Khan, Z. A., Mohammad, A., & Siddiqueed, A. N. (2014). RSM based study of cutting temperature during hard turning with multilayer coated carbide insert. Procedia materials science, 6, 1233-1242.
  15. Soejanto, I. (2009). Desain Eksperimen dengan Metode Taguchi. Yogyakarta: Graha Ilmu
  16. Wang, Z., Wang, N. H., & Li, T. (2011). Computational analysis of a twin-electrode DC submerged arc furnace for MgO crystal production. Journal of Materials Processing Technology, 11(3), 388–395

Last update:

No citation recorded.

Last update: 2024-11-25 11:29:52

No citation recorded.