Jurusan Kimia, Fakultas Matematika dan Ilmu Pengetahuan Alam, Universitas Riau, Kampus Bina Widya km 12,5 Simpang Baru, Tampan, Pekanbaru, Indonesia
BibTex Citation Data :
@article{JKSA47306, author = {Rahmat Zikri and Evelin Natasyah and Muhdarina Muhdarina}, title = {Synthesis of Oil Palm Fronds Charcoal as Adsorbent to Reduce Levels of Fe (III) in Peat Water}, journal = {Jurnal Kimia Sains dan Aplikasi}, volume = {25}, number = {8}, year = {2022}, keywords = {Charcoal; Oil palm fronds; Peat water}, abstract = { The high content of carbon compounds in palm fronds (OPF) makes them potentially useful as an adsorbent. The carbonization method was used for the adsorbent synthesis process. This process began with collecting palm frond waste and then drying and sifting the adsorbent particle. This process resulted in the escape particles with a size of 80 mesh and suspended particles with 120 mesh. Then this process continued by carbonizing the palm fronds with temperature variations starting from (400, 500, and 600°C) for 60 minutes to obtain Charcoal Oil Palm Fronts (COPF). The obtained COPF was determined for moisture and ash content and characterized using FTIR, XRD, and SEM to determine the surface, functional groups, degree of amorphism, crystallinity, and surface morphology. The adsorption efficiency of COPF was applied to the adsorption of Fe (III) in peat water under varying contact time, adsorbent mass, and peat water volume conditions. The water and ash content of COPF qualify the technical quality requirements for activated charcoal according to SNI 06-3730-1995. FTIR analysis detected the presence of vibrations of the C-O, O-H, C=O, C-C, and C-H functional groups on the COPF surface. The XRD pattern showed the existence of a semi-crystalline (002) and (100) plane structure, which is shown at scattering angles of 2θ = 22 o and 42 o . The surface morphology of COPF showed that as the carbonization temperature increased, the number of pores formed increased, and the pore size decreased. The best adsorption test results were obtained with a contact time of 30 minutes, an adsorbent mass of 1.00 g, and a peat water volume of 100 mL. The highest Fe adsorption efficiency was achieved by COPF 500, where the adsorbed mass was 0.054 mg. Increasing the carbonization temperature causes the water content to decrease and the ash content to increase. High water content and ash content cause a decrease in adsorption efficiency because they can cover the pores of the adsorbent. }, issn = {2597-9914}, pages = {300--306} doi = {10.14710/jksa.25.8.300-306}, url = {https://ejournal.undip.ac.id/index.php/ksa/article/view/47306} }
Refworks Citation Data :
The high content of carbon compounds in palm fronds (OPF) makes them potentially useful as an adsorbent. The carbonization method was used for the adsorbent synthesis process. This process began with collecting palm frond waste and then drying and sifting the adsorbent particle. This process resulted in the escape particles with a size of 80 mesh and suspended particles with 120 mesh. Then this process continued by carbonizing the palm fronds with temperature variations starting from (400, 500, and 600°C) for 60 minutes to obtain Charcoal Oil Palm Fronts (COPF). The obtained COPF was determined for moisture and ash content and characterized using FTIR, XRD, and SEM to determine the surface, functional groups, degree of amorphism, crystallinity, and surface morphology. The adsorption efficiency of COPF was applied to the adsorption of Fe (III) in peat water under varying contact time, adsorbent mass, and peat water volume conditions. The water and ash content of COPF qualify the technical quality requirements for activated charcoal according to SNI 06-3730-1995. FTIR analysis detected the presence of vibrations of the C-O, O-H, C=O, C-C, and C-H functional groups on the COPF surface. The XRD pattern showed the existence of a semi-crystalline (002) and (100) plane structure, which is shown at scattering angles of 2θ = 22o and 42o. The surface morphology of COPF showed that as the carbonization temperature increased, the number of pores formed increased, and the pore size decreased. The best adsorption test results were obtained with a contact time of 30 minutes, an adsorbent mass of 1.00 g, and a peat water volume of 100 mL. The highest Fe adsorption efficiency was achieved by COPF 500, where the adsorbed mass was 0.054 mg. Increasing the carbonization temperature causes the water content to decrease and the ash content to increase. High water content and ash content cause a decrease in adsorption efficiency because they can cover the pores of the adsorbent.
Article Metrics:
Last update:
Last update: 2026-09-05 15:26:25
As an article writer, the author has the right to use their article for various purposes, including use by institutions that employ the author or institutions that provide funding for the research. These author rights are granted without special permission.
Authors who publish a paper in JKSA have broad rights to use their work for teaching and scientific purposes without the need to request permission, including: (i) teaching in the author's class or institution; (ii) presenting the work at meetings or conferences and distributing copies to participants; (iii) using the work in training conducted by the author or the author's institution; (iv) distributing copies to colleagues for research purposes; (v) using the work in the compilation of subsequent works by the author; (vi) including the work in a thesis or dissertation; (vii) reusing part of the article in another work, with appropriate citation; (viii) preparing derivative works, with appropriate citation; and (ix) voluntarily posting the work on open websites operated by the author or the author's institution for scientific purposes, in accordance with the CC BY-SA License.
Authors and readers may copy and redistribute the material in any medium or format, and may remix, transform, and build upon the material for any purpose, provided that they give appropriate credit by citing the article or its content, provide a link to the license, and indicate if changes were made.
The authors submitting a manuscript do so on the understanding that, if accepted for publication, the copyright of the article shall be assigned to Jurnal Kimia Sains dan Aplikasi (JKSA). Copyright encompasses the rights to reproduce and distribute the article in all forms and media, including reprints, photographs, microfilms, and any other similar reproductions, as well as translations.
Reproducing any part of this journal, storing it in a database, or transmitting it in any form or medium is permitted without written permission from JKSA. However, the original source must be properly cited in accordance with academic conventions.
JKSA, the Chemistry Department of Diponegoro University, and the Editor make every effort to ensure that no inaccurate, false, or misleading data, opinions, or statements are published in JKSA. However, the content of each article is the sole and exclusive responsibility of its authors.
The Copyright Transfer Form can be downloaded here: [Copyright Transfer Form - Indonesian] [Copyright Transfer Form - English]. The copyright form should bear the authors' original signatures and be sent to the Editor as a printed document, a scanned document sent via email, or by fax.
Prof. Adi Darmawan, Ph.D (Editor in Chief)
Editor in chief of Jurnal Kimia Sains dan Aplikasi (JKSA)
Chemistry Department, Faculty of Sciences and Mathematics, Diponegoro University
Visitor: View My Stats
Jurnal Kimia Sains dan Aplikasi is indexed in:
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
