DOI: https://doi.org/10.14710/ijred.2023.51785

Performance enhancement and emissions reduction in a diesel engine using oleander and croton biodiesel doped with graphene nanoparticles

1Institute of Energy and Environmental Technology, Jomo Kenyatta University of Agriculture and Technology, Nairobi, Kenya

2Department of Mechanical Engineering, Jomo Kenyatta University of Agriculture and Technology, Nairobi, Kenya

3Department of Energy, Gas and Petroleum Engineering, Kenyatta University, Nairobi, Kenya

Received: 14 Jan 2023; Revised: 17 Apr 2023; Accepted: 3 May 2023; Published: 15 May 2023.
Editor(s): Anh-Tuan Le
Open Access Copyright (c) 2023 The Author(s). Published by Centre of Biomass and Renewable Energy (CBIORE)
Creative Commons License This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Citation Format:
Abstract

Biodiesel is considered a suitable substitute for petroleum diesel because it is renewable, environment-friendly, and has a low carbon footprint. However, its high density, high viscosity and low heating value prevents it from replacing petroleum diesel completely. This study investigates the performance and emission characteristics of a compression ignition engine operating on oleander and croton biodiesel doped with graphene nanoparticles. Five fuel samples are used, including diesel (D100), diesel - 80% blended with oleander and croton biodiesel - 20% (OCB20) and OCB20 dosed with graphene nanoparticles at mass fractions of 50 ppm (mg/L), 75 ppm (mg/L) and 100 ppm (mg/L), respectively. The chemical composition of biodiesel and graphene nanoparticles is analyzed using Fourier Transform Infrared (FTIR) spectroscopy while the morphology of the nanoparticles is analyzed using Scanning Electron Microscope (SEM). Engine tests reveal a significant improvement in brake thermal efficiency, especially at 75 ppm concentration which is 2.76%  and 18.93% higher than diesel and OCB20, respectively, and a reduction in brake specific fuel consumption by 2.44% and 16.67% compared to diesel and OCB20, respectively. Carbon monoxide (CO) and unburnt hydrocarbon emissions (UHC) decreases for the 50 ppm sample, recording 8.58% and 21.65% reduction in CO and 52.2% and 50% in UHC compared to the diesel and OCB20, respectively. However, Oxides of Nitrogen (NOx) emissions increase. The results indicate that graphene nanoparticle-enhanced biodiesel can adequately substitute petroleum diesel, albeit with NOx reduction techniques.

 

Fulltext View|Download
Keywords: Biodiesel; Compression ignition engine; Emission; Nano additives; Engine Performance

Article Metrics:

Article Info
Section: Original Research Article
Language : EN
Recent articles
Design, optimization and economic viability of an industrial low temperature hot water production system in Algeria: A case study Utilization of the spent catalyst as a raw material for rechargeable battery production: The effect of leaching time, type, and concentration of organic acids Optimal power flow solutions to power systems with wind energy using a highly effective meta-heuristic algorithm More recent articles
Most cited articles
Phase Change Material on Augmentation of Fresh Water Production Using Pyramid Solar Still Monitoring the performances of a maximum power point tracking photovoltaic (MPPT PV) pumping system driven by a brushless direct current (BLDC) motor Performance Evaluation of the Effect of waste paper on Groundnut Shell Briquette The Use of Odd and Even Class Wind Speed Time Series of Distribution Histogram to Estimate Weibull Parameters Utilization of Iles-Iles and Sorghum Starch for Bioethanol Production More cited articles
  1. Abbasi, E., Akbarzadeh, A., Kouhi, M., & Milani, M. (2016). Graphene: Synthesis, bio-applications, and properties. Artificial Cells, Nanomedicine and Biotechnology, 44(1), 150–156. https://doi.org/10.3109/21691401.2014.927880
  2. Agarwal, A. K., Gupta, J. G., & Dhar, A. (2017). Potential and challenges for large-scale application of biodiesel in automotive sector. Progress in Energy and Combustion Science, 61, 113-149; https://doi.org/10.1016/j.pecs.2017.03.002
  3. Antidormi, A., Colombo, L., & Roche, S. (2022). Emerging properties of non-crystalline phases of graphene and boron nitride based materials. Nano Materials Science, 4 (1), 10-17; https://doi.org/10.1016/j.nanoms.2021.03.003
  4. Basumatary, S., & Deka, D. C. (2014). Transesterification of yellow oleander (Thevetia peruviana) seed oil to fatty acid methyl esters (biodiesel) using a heterogeneous catalyst derived from rhizome of Musa balbisiana colla. International Journal of ChemTech Research, 6, 2377–2384. https://sphinxsai.com/2014/vol6pt4/3/(2377-2384)Jul-Aug14.pdf
  5. Begag, A., Saim, R., Abboudi, S., & Öztop, H. F. (2021). Effect of internal and external corrugated surfaces on the characteristics of heat transfer and pressure drop in a concentric tube heat exchanger. International Journal of Thermal Sciences 165; https://doi.org/10.1016/j.ijthermalsci.2021.106930
  6. Bhagwat, V. A., Pawar, C., & Banapurmath, N. R. (2015). Graphene Nanoparticle - Biodiesel Blended Diesel Engine. International Journal of Engineering Research & Technology (IJERT), 4(02), 75–78. https://www.ijert.org/research/graphene-nanoparticle-biodiesel-blended-diesel-engine-IJERTV4IS020094.pdf
  7. Bhattacharyya, S. (2022). Transesterification of Yellow Oleander seed oil, its utilization as biodiesel and performance evaluation. In Heliyon, 8(4); https://doi.org/10.1016/j.heliyon.2022.e09250
  8. Chehroudi, B. (2016). Applications of Graphene in Fuel Propellant Combustion. Applications of Graphene in Fuel/Propellant Combustion. Graphene Science Handbook, https://www.advtechconsultants.com
  9. Coronado, M. A., Montero, G., García, C., Valdez, B., Ayala, R., & Pérez, A. (2017). Quality assessment of biodiesel blends proposed by the new Mexican policy framework. Energies, 10(5), 631; https://doi.org/10.3390/en10050631
  10. Daud, S., Hamidi, M. A., & Mamat, R. (2022). A review of fuel additives’ effects and predictions on internal combustion engine performance and emissions. AIMS Energy, 10(1), 1-22; https://doi.org/10.3934/ENERGY.2022001
  11. Debbarma, S., Misra, R. D., & Das, B. (2020). Performance of graphene-added palm biodiesel in a diesel engine. Clean Technologies and Environmental Policy, 22(2), 523–534. https://doi.org/10.1007/s10098-019-01800-2
  12. Deng, S., & Berry, V. (2016). Wrinkled, rippled and crumpled graphene : an overview of formation mechanism , electronic properties , and applications. Biochemical Pharmacology, 19(4), 197–212. https://doi.org/10.1016/j.mattod.2015.10.002
  13. Devarajan, Y., Munuswamy, D. B., & Mahalingam, A. (2018). Influence of nano-additive on performance and emission characteristics of a diesel engine running on neat neem oil biodiesel. In Environmental Science and Pollution Research 25(26), 26167-72; https://doi.org/10.1007/s11356-018-2618-6
  14. EL-Seesy, A. I., & Hassan, H. (2019). Combustion characteristics of a diesel engine fueled by biodiesel-diesel-n-butanol blend and titanium oxide additives. Energy Procedia, 162 , 48–56. https://doi.org/10.1016/j.egypro.2019.04.006
  15. El-Seesy, A. I., Hassan, H., & Ookawara, S. (2018). Effects of graphene nanoplatelet addition to jatropha Biodiesel–Diesel mixture on the performance and emission characteristics of a diesel engine. Energy, 147, 1129–1152; https://doi.org/10.1016/j.energy.2018.01.108
  16. Fazal, M. A., Haseeb, A. S. M. A., & Masjuki, H. H. (2013). Investigation of friction and wear characteristics of palm biodiesel. In Energy Conversion and Management 67(March), 251-256; https://doi.org/10.1016/j.enconman.2012.12.002
  17. Gad, M. S., El-Araby, R., Abed, K. A., El-Ibiari, N. N., El Morsi, A. K., & El-Diwani, G. I. (2018). Performance and emissions characteristics of C.I. engine fueled with palm oil/palm oil methyl ester blended with diesel fuel. Egyptian Journal of Petroleum, 27(2), 215–219. https://doi.org/10.1016/j.ejpe.2017.05.009
  18. Goswami, L., Kim, K. H., Deep, A., Das, P., Bhattacharya, S. S., Kumar, S., & Adelodun, A. A. (2017). Engineered nano particles: Nature, behavior, and effect on the environment. Journal of Environmental Management, 196, 297-315; https://doi.org/10.1016/j.jenvman.2017.01.011
  19. Hanaki, K., & Portugal-Pereira, J. (2018). The Effect of Biofuel Production on Greenhouse Gas Emission Reductions. Biofuels and sustainability (53-71); https://doi.org/10.1007/978-4-431-54895-9_6
  20. Ivanov, I. (2019). Window To the Future. The Current Digest of the Russian Press, 71(048), 17–18. https://doi.org/10.21557/dsp.56774463
  21. Jalaludin, H. A., Abdullah, N. R., Sharudin, H., Asiah, A. R., & Jumali, M. F. (2020). Emission characteristics of biodiesel ratios of 10%, 20%, and, 30% in a single-cylinder diesel engine. IOP Conference Series: Materials Science and Engineering, 834(1). https://doi.org/10.1088/1757-899X/834/1/012066
  22. Jeyaseelan, T., & Chako, N. (2020). Comparative evaluation of graphene oxide and graphene nanoplatelets as fuel additives on the combustion and emission characteristics of a diesel engine fuelled with diesel and biodiesel blend. Fuel Processing Technology, 204, 106406. https://doi.org/10.1016/j.fuproc.2020.106406
  23. Kamel, S., El-Sakhawy, M., Anis, B., & Tohamy, H. A. S. (2019). Graphene’s Structure, Synthesis and Characterization; A brief review. Egyptian Journal of Chemistry, 62(Part 2), 593–608. https://doi.org/10.21608/ejchem.2019.15173.1919
  24. Mahdi, J. M., & Nsofor, E. C. (2017). Melting enhancement in triplex-tube latent heat energy storage system using nanoparticles-metal foam combination. Applied Energy, 191(April), 22-34; https://doi.org/10.1016/j.apenergy.2016.11.036
  25. Mallikarjuna Rao, D., Janga, V. S. R., Dhana Raju, V., & Arifa, S. (2022). Impact of Graphene Nanoparticles Addition to Jatropha Biodiesel Blend on the Performance and Emission Characteristics of a Diesel Engine. Lecture Notes in Mechanical Engineering design and energy technologies, (October), 825–33; https://doi.org/10.1007/978-981-16-4222-7_90
  26. Masera, K., & Hossain, A. K. (2017). Production, Characterisation and Assessment of Biomixture Fuels for Compression Ignition Engine Application. International Journal of Mechanical and Mechatronics Engineering, 11(12), 1857–1863. https://doi.org/10.1999/1307-6892/10008317
  27. Nair, J., Prasad Kumar, P., Thakur, A. K., Samhita, & Aravinda. (2021). Influence on emissions and performance of CI engine with graphene nanoparticles blended with Karanja biodiesel. AIP Conference Proceedings, 2317(February). https://doi.org/10.1063/5.0036142
  28. Nandiyanto, A. B. D., Oktiani, R., & Ragadhita, R. (2019). How to read and interpret ftir spectroscope of organic material. Indonesian Journal of Science and Technology, 4(1), 97–118. https://doi.org/10.17509/ijost.v4i1.15806
  29. Osawa, W. O., Onyari, J. M., Sahoo, P. K., & Mulaa, F. J. (2014). Process optimization for production of biodiesel from croton oil using two-stage process. IOSR Journal of Environmental Science, Toxicology and Food Technology, 8(11), 49–54. https://doi.org/10.9790/2402-081134954
  30. Oseni, M., & Obetta, S. (2012). Evaluation of fatty acids profile of ethyl esters of yellow oleander and groundnut oils as biodiesel feedstock. American Journal of Scientific and Industrial Research, 3(2), 62–68. https://doi.org/10.5251/ajsir.2012.3.2.62.68
  31. Pattanaik, B. P., Jena, J., & Misra, R. D. (2017). The effect of oxygen content in soapnut biodiesel-diesel blends on performance of a diesel engine. International Journal of Automotive and Mechanical Engineering, 14(3), 4574–4588. https://doi.org/10.15282/ijame.14.3.2017.14.0361
  32. Pham, P. X. (2015). Influences of Molecular Profiles of Biodiesels on Atomization, Combustion and Emission Characteristics. PhD. thesis. University of Sydney; https://doi.org/10.13140/2.1.4430.1609
  33. Qasim, M., Ansari, T. M., & Hussain, M. (2017). Combustion, performance, and emission evaluation of a diesel engine with biodiesel like fuel blends derived from a mixture of Pakistani waste canola and waste transformer oils. Energies 10(7), 1023; https://doi.org/10.3390/en10071023
  34. Razzaq, L., Mujtaba, M. A., Elahi, M., Soudagar, M., Ahmed, W., Fayaz, H., Bashir, S., Fattah, I. M. R., Chyuan, H., Shahapurkar, K., Afzal, A., Wageh, S., Al-ghamdi, A., Shujaat, M., & El-seesy, A. I. (2021). Engine performance and emission characteristics of palm biodiesel blends with graphene oxide nanoplatelets and dimethyl carbonate additives. Journal of Environmental Management, 282(October 2020), 111917. https://doi.org/10.1016/j.jenvman.2020.111917
  35. Ruhul, A. M., Kalam, M. A., Masjuki, H. H., Fattah, I. M. R., Reham, S. S., & Rashed, M. M. (2015). State of the art of biodiesel production processes: A review of the heterogeneous catalyst. RSC Advances, 5(122), 101023–101044. https://doi.org/10.1039/c5ra09862a
  36. Sabapathy, S. P., Ammasi, A. M., Khalife, E., Kaveh, M., Szymanek, M., Reghu, G. K., & Sabapathy, P. (2021). Comprehensive assessment from optimum biodiesel yield to combustion characteristics of light duty diesel engine fueled with palm kernel oil biodiesel and fuel additives. Materials, 14(15), 4274; https://doi.org/10.3390/ma14154274
  37. Sang, M., Shin, J., Kim, K., & Yu, K. J. (2019). Electronic and thermal properties of graphene and recent advances in graphene based electronics applications. Nanomaterials, 9(3) 374; https://doi.org/10.3390/nano9030374
  38. Saxena, V., Kumar, N., & Saxena, V. K. (2017). A comprehensive review on combustion and stability aspects of metal nanoparticles and its additive effect on diesel and biodiesel fuelled C.I. engine. Renewable and Sustainable Energy Reviews, 70(April), 563–588); https://doi.org/10.1016/j.rser.2016.11.067
  39. Semakula, M., & Inambao, P. F. (2018). The Formation, Effects and Control of Oxides of Nitrogen in Diesel Engines. International Journal of Applied Engineering Research, 13(6), 3200–3209. https://www.ripublication.com/ijaer18/ijaerv13n6_09.pdf
  40. SiSim, H. S., Yetter, R. A., Connell, T. L., Dabbs, D. M., & Aksay, I. A. (2020). (2020). Multifunctional Graphene-Based Additives for Enhanced Combustion of Cracked Hydrocarbon Fuels under Supercritical Conditions. Combustion Science and Technology, 192(7), 1420–1435. https://doi.org/10.1080/00102202.2020.1737033
  41. Sivasankaran, S., Sivaprasad, K., Narayanasamy, R., & Satyanarayana, P. V. (2011). X-ray peak broadening analysis of AA 6061100−x−xwt.% Al2O3 nanocomposite prepared by mechanical alloying. Materials Characterization, 62(7), 661–672. https://doi.org/10.1016/j.matchar.2011.04.017
  42. Soudagar, M. E. M., Nik-Ghazali, N.-N., Abul Kalam, M., Badruddin, I. A., Banapurmath, N. R., & Akram, N. (2018). The effect of nano-additives in diesel-biodiesel fuel blends: A comprehensive review on stability, engine performance and emission characteristics. Energy Conversion and Management, 178, 146–177. https://doi.org/10.1016/j.enconman.2018.10.019
  43. Soudagar, M. E. M., Nik-Ghazali, N.-N., Kalam, M. A., Badruddin, I. A., Banapurmath, N. R., Bin Ali, M. A., Kamangar, S., Cho, H. M., & Akram, N. (2020). An investigation on the influence of aluminium oxide nano-additive and honge oil methyl ester on engine performance, combustion and emission characteristics. Renewable Energy, 146, 2291–2307. https://doi.org/10.1016/j.renene.2019.08.025
  44. Sunilkumar, T., Manavendra, G., Banapurmath, N.R., Guruchethan, A.M. (2017). Performance and Emission Characteristics of Graphene Nano Particle-Biodiesel Blends Fuelled Diesel Engine. International Research Journal of Engineering and Technology (IRJET), 4(10), 552-557. https://www.irjet.net/archives/V4/i10/IRJET-V4I1096.pdf
  45. Pallone, T. (2018). 13 Reasons Graphene Is a Wonder Material. In https://www.globalspec.com
  46. Ujjain, S. K., Bhatia, R., & Ahuja, P. (2019). Aziridine-functionalized graphene: Effect of aromaticity for aryl functional groups on enhanced power conversion efficiency of organic photovoltaic cells. In Journal of Saudi Chemical Society, 23(6), 655–665; https://doi.org/10.1016/j.jscs.2018.11.006
  47. Wade, Jr., L. G. (2003). IR: Theory and Interpretation of IR spectra presentation, 5th edn, Organic Chemistry, 853–866
  48. Yarkasuwa, C. I., Wilson, D., & Michael, E. (2013). Production of biodiesel from yellow oleander (thevetia peruvian) oil and its biodegradability. Journal of the Korean Chemical Society, 57(3), 377–381. https://doi.org/10.5012/jkcs.2013.57.3.377
  49. Yohannan Panicker, C., Varghese, H. T., & Chandran, A. (2011). Densityfunctional theory and IR spectroscopic study of carboxyl group. Oriental Journal of Chemistry, 27(4), 1771–1774. https://www.orientjchem.org/?p=24331

Last update:

  1. Nanoparticle-enhanced biodiesel blends: A comprehensive review on improving engine performance and emissions

    Veeranna Modi, Prasad B. Rampure, Atul Babbar, Raman Kumar, Madeva Nagaral, Abhijit Bhowmik, Raman Kumar, Shatrudhan Pandey, S.M. Mozammil Hasnain, Muhammad Mahmood Ali, Muhammad Nasir Bashir. Materials Science for Energy Technologies, 7 , 2024. doi: 10.1016/j.mset.2024.02.001

  2. Effects of CeO 2 nanoparticles on engine features, tribology behaviors, and environment

    Thanh Tuan Le, Inbanaathan Papla Venugopal, Thanh Hai Truong, Dao Nam Cao, Huu Cuong Le, Xuan Phuong Nguyen. Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, 45 (3), 2023. doi: 10.1080/15567036.2023.2231387

  3. Nanotechnology-based biodiesel: A comprehensive review on production, and utilization in diesel engine as a substitute of diesel fuel

    Thanh Tuan Le, Minh Ho Tran, Quang Chien Nguyen, Huu Cuong Le, Van Quy Nguyen, Dao Nam Cao, Prabhu Paramasivam. International Journal of Renewable Energy Development, 13 (3), 2024. doi: 10.61435/ijred.2024.60126

  4. Effects of CeO2 nanoparticles on engine features, tribology behaviors, and environment

    Thanh Tuan Le, Inbanaathan Papla Venugopal, Thanh Hai Truong, Dao Nam Cao, Huu Cuong Le, Xuan Phuong Nguyen. Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, 45 (3), 2023. doi: 10.1080/15567036.2023.2231387

  5. Optimization of Biodiesel–Nanoparticle Blends for Enhanced Diesel Engine Performance and Emission Reduction

    Yasmeen A. Mikky, Ahmed A. Bhran, Reham Y. El-Araby, Adel M. A. Mohamed, Abdelrahman G. Gadallah, Abeer M. Shoaib. Processes, 12 (11), 2024. doi: 10.3390/pr12112471

Last update: 2024-12-26 17:05:27

No citation recorded.