DOI: https://doi.org/10.14710/ijred.3.1.13-20

Characteristics of Waste Plastics Pyrolytic Oil and Its Applications as Alternative Fuel on Four Cylinder Diesel Engines

1Department of Mechanical and Industrial Engineering Faculty of Engineering, Gadjah Mada University, Yogyakarta, Indonesia

2Department of Mechanical and Industrial Engineering Faculty of Engineering, Gadjah Mada University, Yogyakarta, Indonesia

Published: 15 Feb 2014.
Editor(s):

Citation Format:
Abstract
Waste plastics recycling using pyrolysis method is not only able to decrease a number of environment pollutant but also able to produce economical and high quality hydrocarbon products. Two experiments were conducted to completely study Waste Plastic Pyrolytic Oil (WPPO) characteristics and its applications.  First experiment investigated oil characteristics derived from pyrolysis process in two stages batch reactors: pyrolysis and catalytic reforming reactor, at maximum temperature 500oC and 450oC respectively. Waste Polyethylene (PE), Polypropylene (PP), Polystyrene (PS), Polyethylene Terepthalate (PET) and others were used as raw material. Nitrogen flow rate at 0.8 l/minutes was used to increase oil weight percentage. Indonesian natural zeolite was used as catalyst. Then, second experiment was carried out on Diesel Engine Test Bed (DETB) used blending of WPPO and Biodiesel fuel with a volume ratio of 1:9. This experiment was specifically conducted to study how much potency of blending of WPPO and biodiesel in diesel engine. The result of first experiment showed that the highest weight percentage of WPPO derived from mixture of PE waste (50%wt), PP waste (40%wt) and PS waste (10%wt) is 45.13%wt. The more weight percentage of PE in feedstock effected on the less weight percentage of WPPO, the more percentage of C12-C20 content in WPPO and the higher calorific value of WPPO. Characteristics of WPPO such as, Specific Gravity, Flash point, Pour Point, Kinematic Viscosity, Calorific value and percentage of C12-C20 showed interesting result that WPPO could be developed as alternative fuel on diesel fuel blending due to the proximity of their characteristics. Performance of diesel engine using blending of WPPO and biodiesel on second experiment gave good result so the WPPO will have great potency to be valuable alternative liquid fuel in future, especially on stationary diesel engine and transportation engine application.
Fulltext View|Download
Keywords: diesel; fuel; pyrolysis; pyrolytic oil; waste plastic

Article Metrics:

Article Info
Section: Original Research Article
Language : EN
Recent articles
Assessing The Current Indonesia’s Electricity Market Arrangements and The Opportunities to Reform Characteristics of Waste Plastics Pyrolytic Oil and Its Applications as Alternative Fuel on Four Cylinder Diesel Engines Soybean Opportunity as Source of New Energy in Indonesia More recent articles
Most cited articles
Thermal Performance Improvement of the Heat Pipe by Employing Dolomite/Ethylene Glycol Nanofluid Combustion characteristics of diesel engine using producer gas and blends of Jatropha methyl ester with diesel in mixed fuel mode Design, Analysis and Optimization of a Solar Dish/Stirling System Automatic and Online Detection of Rotor Fault State Improving Stability and Convergence for Adaptive Radial Basis Function Neural Networks Algorithm. (On-Line Harmonics Estimation Application) More cited articles
  1. Achilias, D.S., Antonakou E., Roupakias C., Megalokonomos P. & Lappas A. (2008) Recycling techniques of polyelefins from plastic waste. Global NEST Journal, 10(1), 114-122
  2. Behera, P.& Marugan, S. (2013) Combustion, performance and emsission parameters of used transformer oil and its diesel blends in DI diesel engine.Journal of Fuel, 104, 147-154 https://doi.org/10.1016/j.fuel.2012.09.077
  3. Berrueco, C., Mastral, J.F.& Ceamanos, J. (2007) Modeling of the pyrolysis of high density polyethylene: product distribution in a fluidized bed reactor. Journal of Analytical and Applied Pyrolysis, 79, 313-322 https://doi.org/10.1016/j.jaap.2006.10.018
  4. Bousteead, I. (1997) Eco-Profiles of European Plastics Industry, Report 4: Polystyrene,2ndEdition, Association of plastics manufactures in Europe, Brussels, Belgium
  5. Ghoshal, A.K., Saha, B.& Karthik Reddy, P. (2008) Hybrid genetic algorithm to find the best model and the globally optimized overall kinetics parameters for thermal decomposition of plastics. Chemical Engineering Journal, 138, 20-29 https://doi.org/10.1016/j.cej.2007.05.024
  6. Gunthur, R., Kumar, D.& Reddy, VK. (2011) Experiment evaluation a diesel engine with blends of diesel-plastic pyrolysis oil, International Journal of Engineering Science and Technology, ISSN: 0975-5462
  7. Scheirs, J.& Kaminsky W. (2006) Feedstock Recycling and Pyrolysis of Waste Plastics: Converting Waste Plastics into Diesel and Other Fuels, ISBN: 0-470-02152-7, John Wiley & Sons Ltd, Chichester. https://doi.org/10.1002/0470021543
  8. Karaduman, A., Simsek, E.H.,Cicek, B.& Bilgesü, A.Y. (2001) Flash pyrolysis of polystyrene wastes in a free-fall reactor under vacuum. Journal of Analytical and Applied Pyrolysis, 60, 179-186 https://doi.org/10.1016/S0165-2370(00)00169-8
  9. Kementrian Negara Riset dan Teknologi Republik Indonesia. (2006) Buku Putih Penelitian, Pengembangan dan Penerapan Ilmu Pengetahuan dan teknologi Bidang Sumber Energi Baru dan Terbarukan untuk Mendukung Keamanan Ketersediaan Energi Tahun 2005 -2025, Jakarta
  10. Kumar, S., Panda A.K Singh R.K. (2011) A review of tertiary of high-density polyethylene to fuel.Journal of Resources, conversion and recycling, 55, 893-910 https://doi.org/10.1016/j.resconrec.2011.05.005
  11. Lardinois, I.&van de Klundert, A. (1995) Plastic Waste. Options forSmall-Scale Resource Recovery. TOOL Publications, AmsterdamLin, Y.H. (2009) Production of valuable hydrocarbons bycatalytic degradation of a mixture of post-consumer plastic waste in a fluidized-bed reactor. Journal of Polymer Degradation and Stability, 1924-1931 https://doi.org/10.1016/j.polymdegradstab.2009.08.004
  12. Lopez, A., Marco, I., Cabllero, D.M., Laresgoiti M.F.&Adrados(2011) Influence of time and temperature on pyrolysis plasticwastes in a semi-batch reactor.Chemical Engineering Journal, 173, 62-71 https://doi.org/10.1016/j.cej.2011.07.037
  13. Mani, M., Nagarajan G.& Sampath S. (2010) An experiment on a DI diesel engine using waste plastic oilwith exhaust gas recirculation.Journal of Fuel, 89, 1826-1823 https://doi.org/10.1016/j.fuel.2009.11.009
  14. Marcilla, A., Hernández, M.R., Gómez, A., García, A.N.& Agulló, J. (2007) Effect of the temperature in the nature and extension of the primary and secondary reactions in the thermal and HZSM-5 catalytic pyrolysis of HDPE. Applied Catalysis A: General, 317, 183-194 https://doi.org/10.1016/j.apcata.2006.10.017
  15. Pratama, N.N. (2012) Analisis Karakteristik minyak hasil pirolisis plastik Polyethylene, Polypropylene dan Polystyrene, Bachelor Thesis. Mechanical and Industrial engineering Department, UGM, Yogyakarta
  16. Pratoomyod J.& Laohalidanond K. (2013) Perfomance and emission of blends of diesel fuel with wasteplastic oil in a diesel engine.International Journal of Engineering Science and Technology, ISSN: 2319-5967
  17. Serrano, D.P., Aguardo, J., Escola, J.M.& Garagorri, E. (2001) Conversion of low density polyethylene into petrochemical feedstock using a continuous screw kiln reactor.Journal of Analytical and Applied Pyrolysis, 58-59, 789-801 https://doi.org/10.1016/S0165-2370(00)00153-4
  18. Williams, P.T.& Badri, R. (2004) Hydrocarbon gases and soils from the recycling of polystyrene waste by catalytic pyrolysis.International Journal of Energy Research, 28, 31-44 https://doi.org/10.1002/er.949

Last update:

  1. Review on production of liquid fuel from plastic wastes through thermal and catalytic degradation

    Biswajit Saha, Sundaramurthy Vedachalam, Ajay K. Dalai, Saumitra Saxena, Bassam Dally, William L. Roberts. Journal of the Energy Institute, 114 , 2024. doi: 10.1016/j.joei.2024.101661

  2. Distilled Waste Plastic Oil as Fuel for a Diesel Engine: Fuel Production, Combustion Characteristics, and Exhaust Gas Emissions

    Weerachai Arjharn, Pansa Liplap, Somkiat Maithomklang, Kontorn Thammakul, Sathaporn Chuepeng, Ekarong Sukjit. ACS Omega, 7 (11), 2022. doi: 10.1021/acsomega.1c07257

  3. An Industrial Perspective for Sustainable Polypropylene Plastic Waste Management via Catalytic Pyrolysis—A Technical Report

    Andromachi Chasioti, Anastasia Zabaniotou. Sustainability, 16 (14), 2024. doi: 10.3390/su16145852

  4. Dynamics of Transportation Ecosystem, Modeling, and Control

    Abiodun Oluwatosin Adeoye, Jibrin Muhammad Yelwa, Naziru Imam, Rukayat Oluwatobiloba Quadri, Olayide Samuel Lawal, Dosu Malomo, Samson Abiodun Aasa, Augustine Eyikwuojo Onakpa, Ruth Kooaka Dorgbaa, Busuyi Patrick Omoniyi, Nuhu Ahmad, Husaina Anchau Garba. Energy, Environment, and Sustainability, 2024. doi: 10.1007/978-981-97-0437-8_11

  5. Characterization and Impact of Waste Plastic Oil in a Variable Compression Ratio Diesel Engine

    Khatha Wathakit, Ekarong Sukjit, Chalita Kaewbuddee, Somkiat Maithomklang, Niti Klinkaew, Pansa Liplap, Weerachai Arjharn, Jiraphon Srisertpol. Energies, 14 (8), 2021. doi: 10.3390/en14082230

  6. INFLUENCE OF ZnO, Al2O3, CeO2 NANOPARTICLE-ADDED JULIFLORA BIODIESEL HRF ON RCCI ENGINE’S PERFORMANCE

    RAMACHANDRAN MANIVANNAN, NEELAKRISHNAN SUBRAMANYAN. Surface Review and Letters, 31 (07), 2024. doi: 10.1142/S0218625X24500574

  7. Proceedings of the 3rd International Conference on Experimental and Computational Mechanics in Engineering

    Thaharul Fikri, Ahmad Syuhada, Razali Thaib. Lecture Notes in Mechanical Engineering, 2023. doi: 10.1007/978-981-19-3629-6_25

  8. Plastics waste management: A review of pyrolysis technology

    Wilson Uzochukwu Eze, Reginald Umunakwe, Henry Chinedu Obasi, Michael Ifeanyichukwu Ugbaja, Cosmas Chinedu Uche, Innocent Chimezie Madufor. Clean Technologies and Recycling, 1 (1), 2021. doi: 10.3934/ctr.2021003

  9. Combustion of char from plastic wastes pyrolysis

    Harwin Saptoadi, Tri Agung Rohmat, Sutoyo. AIP Conference Proceedings, 1737 , 2016. doi: 10.1063/1.4949286

  10. Fuel Properties, Performance and Emission of Alternative Fuel from Pyrolysis of Waste Plastics

    W Khatha, S Ekarong, M Somkiat, S Jiraphon. IOP Conference Series: Materials Science and Engineering, 717 (1), 2020. doi: 10.1088/1757-899X/717/1/012001

  11. A review on feasibility and techno-economic analysis of hydrocarbon liquid fuels production via catalytic pyrolysis of waste plastic materials

    Bablu Alawa, Sankar Chakma. Carbon Capture Science & Technology, 14 , 2025. doi: 10.1016/j.ccst.2024.100337

  12. Advanced Materials and Conversion Technologies for Personal Protective Equipment Used in the COVID-19 Pandemic

    S. Sakthivel, R. Prasanna Venkatesh, Suresh Sundaramurthy. Materials Horizons: From Nature to Nanomaterials, 2024. doi: 10.1007/978-981-97-4692-7_9

  13. Two stage co-pyrolysis improvement to produce synthetic oil and gas simultaneously from mixed municipal solid waste using natural dolomite-based catalyst

    Indra Mamad Gandidi, Edy Suryadi, Efri Mardawati, Dwi Rustam Kendarto, Nugroho Agung Pambudi. Results in Engineering, 16 , 2022. doi: 10.1016/j.rineng.2022.100753

  14. Review of personal protective equipment and their associated wastes, life-cycle and effective management during the Covid-19 pandemic in developing nations

    Wilson U. Eze, Toyese Oyegoke, Jonathan D. Gaiya, Reginald Umunakwe, David I. Onyemachi. Clean Technologies and Recycling, 2 (1), 2022. doi: 10.3934/ctr.2022001

  15. PoP (pyrolysis of plastic): Utilisation of plastic waste as raw material of liquid fuel production using pyrolysis method

    llovine Hadassa Enggar, Juliet Patricia Arsadha, Mohamad Zaky Nugraha, Bazlina Dawami Afrah, M. Ihsan Riady. TOWARD ADAPTIVE RESEARCH AND TECHNOLOGY DEVELOPMENT FOR FUTURE LIFE, 2689 , 2023. doi: 10.1063/5.0114768

  16. Feasibility and Techno-Economic Analysis of Hydrocarbon Liquid Fuels Production via Catalytic Pyrolysis of Waste Plastic Materials

    Bablu Alawa, Sankar Chakma. Carbon Capture Science & Technology, 2024. doi: 10.1016/j.ccst.2024.100337

  17. Economic Assessment of Polypropylene Waste (PP) Pyrolysis in Circular Economy and Industrial Symbiosis

    Anastasia Zabaniotou, Ioannis Vaskalis. Energies, 16 (2), 2023. doi: 10.3390/en16020593

  18. Characterisation of Fractionated oil from Pyrolysis of Low-Density Polyethylene: Comparison between Catalytic Process and Non-Catalytic Process

    Olugbenga Oludayo Oluwasina, Osaretin Edwin Omoruyi, Gbenga Emmanuel Adekayero, Olabiyi Julius Akinwumi, Adebisi Olayinka Akinola, Babatunde Abraham Okunlol, Labunmi Lajide. International Journal of Innovative Science and Research Technology (IJISRT), 2024. doi: 10.38124/ijisrt/IJISRT24MAY1604

  19. Utilization of Plastics Waste Oil as Partial Substitute for Kerosene in Pressurized Cookstoves

    Harwin Saptoadi, Nosal N. Pratama. International Journal of Environmental Science and Development, 6 (4), 2015. doi: 10.7763/IJESD.2015.V6.619

  20. Performance Test of A mixture of Polypropylene Plastic Fuel from Pyrolisis with Gasoline to Torque and engine Power

    Aditya Wahyu Pratama, Winarko. Journal of Physics: Conference Series, 1569 , 2020. doi: 10.1088/1742-6596/1569/3/032045

Last update: 2024-12-25 20:34:35

  1. Combustion of char from plastic wastes pyrolysis

    Harwin Saptoadi, Tri Agung Rohmat, Sutoyo. AIP Conference Proceedings, 1737 , 2016. doi: 10.1063/1.4949286

  2. Fuel Properties, Performance and Emission of Alternative Fuel from Pyrolysis of Waste Plastics

    W Khatha, S Ekarong, M Somkiat, S Jiraphon. IOP Conference Series: Materials Science and Engineering, 717 (1), 2020. doi: 10.1088/1757-899X/717/1/012001

  3. Thermal decomposition and kinetic studies of pyrolysis of Spirulina platensis residue

    Jamilatun S.. International Journal of Renewable Energy Development, 6 (3), 2017. doi: 10.14710/ijred.6.3.193-201

  4. Performance Test of A mixture of Polypropylene Plastic Fuel from Pyrolisis with Gasoline to Torque and engine Power

    Aditya Wahyu Pratama, Winarko. Journal of Physics: Conference Series, 1569 , 2020. doi: 10.1088/1742-6596/1569/3/032045