skip to main content

Advanced Loop Thermosiphon With Check Valve (ALT/CV): Thermal Performance and Behavior

Heat Pipe and Nanofluid Technology Research Unit, King Mongkut’s University of Technology North Bangkok, Thailand

Received: 28 Oct 2020; Revised: 17 Dec 2020; Accepted: 31 Dec 2020; Available online: 2 Jan 2021; Published: 1 May 2021.
Editor(s): H. Hadiyanto
Open Access Copyright (c) 2021 The Authors. Published by Centre of Biomass and Renewable Energy (CBIORE)
Creative Commons License This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Citation Format:
Abstract
Nanofluids (NFs) are an attractive alternative to traditional working fluids for thermosiphons, but the solid nanoparticles (NPs) within the NF can agglomerate and reduce the thermal performance. This study focused on clarifying the effect of a NF with surfactants on the heat transfer characteristics of an advanced loop thermosiphon with a check valve (ALT/CV). In an experiment, the ALT/CV was filled with different working fluids at filling ratios of 30%, 50%, and 80% with respect to the evaporator volume. Heat was supplied at 20%, 40%, 60%, 80%, and 100% of the heater output (2000 W). Five working fluids were considered: deionized (DI) water, a DI water-based NF with 0.5 wt% silver NPs, and the same NF containing 0.5, 1, and 1.5 wt% oleic acid (OA) and potassium oleate (OAK+) as surfactants. The results showed that the ALT/CV provided a better heat transfer performance than a normal thermosiphon. The maximum heat transfer rate was achieved with the NF containing 0.5 wt% silver NPs and 1 wt% OAK+. The NF containing OAK+ demonstrated a heat transfer rate approximately 80% higher than that of the DI water
Fulltext View|Download
Keywords: Loop thermosyphon; Check value; Nanofluids; Surfactant; Potassium oleate
Funding: King Mongkut’s University of Technology North Bangkok

Article Metrics:

  1. Amtachaya W., P and Srimuang. 2010. “Comparative Heat Transfer Characteristics of a Flat Two-Phase Closed Thermosyphon (FTPCT) and a Conventional Two-Phase Closed Thermosyphon (CTPCT).” Heat and Mass Transfer 37: 293–98. https://doi.org/10.1016/j.icheatmasstransfer.2009.11.004
  2. Anon. 1980. Heat Pipes-General Information on Their Use, Operation and Design, Data Item No. 80013. . London: Engineering : Sciences Data Unit
  3. Bhuwakietkumjohn, N, and T Parametthanuwat. 2017. “Heat Transfer Behaviour of Silver Particles Containing Oleic Acid Surfactant: Application in a Two Phase Closed Rectangular Cross Sectional Thermosyphon (RTPTC).” Heat and Mass Transfer 53 (1): 37–48. https://doi.org/10.1007/s00231-016-1798-1
  4. Bhuwakietkumjohn, N, and S Rittidech. 2010. “Internal Flow Patterns on Heat Transfer Characteristics of a Closed-Loop Oscillating Heat-Pipe with Check Valves Using Ethanol and a Silver Nano-Ethanol Mixture.” Experimental Thermal and Fluid Science 34 (8): 1000–1007. https://doi.org/http://dx.doi.org/10.1016/j.expthermflusci.2010.03.003
  5. Brusly Solomon, A, Arun Mathew, K Ramachandran, B C Pillai, and V K Karthikeyan. 2013. “Thermal Performance of Anodized Two Phase Closed Thermosyphon (TPCT).” Experimental Thermal and Fluid Science 48: 49–57. https://doi.org/http://dx.doi.org/10.1016/j.expthermflusci.2013.02.007
  6. Buongiorno, Jacopo, David C Venerus, Naveen Prabhat, Thomas McKrell, Jessica Townsend, Rebecca Christianson, Yuriy V Tolmachev, et al. 2009. “A Benchmark Study on the Thermal Conductivity of Nanofluids.” Journal of Applied Physics 106 (9). https://doi.org/09431210.1063/1.3245330
  7. Choi J.A., S U S and Eastman. 1995. “Enhancing Thermal Conductivity of Fluids with Nano-Particles.” Int. Mech. Eng. Congr. Exhib
  8. Dangeton, W, A Pattiya, S Rittidech, and N Siriwan. 2012. “Flow Visualization of a Miniature Loop Thermosyphon.” Experimental Heat Transfer 26 (4): 329–42. https://doi.org/10.1080/08916152.2012.657743
  9. Faghri, A. 1995. Heat Pipe Science and Technology. 1st ed. Washington, DC: Taylor&Francis
  10. Fumito, K, F Chowdhury, W Hideaki, and M Kunihito. 2003. “Heat Transfer Characteristics in an Evaporator Section of a Looped Parallel Thermosyphon.” The 7th International Heat Pipe Symposium. Jeju, Korea, 2003
  11. Godson, L, B Raja, D M Lal, and S Wongwises. 2010. “Experimental Investigation on the Thermal Conductivity and Viscosity of Silver-Deionized Water Nanofluid.” Experimental Heat Transfer 23 (4): 317–32. https://doi.org/10.1080/08916150903564796
  12. Hojjat, M, S G Etemad, R Bagheri, and J Thibault. 2011. “Rheological Characteristics of Non-Newtonian Nanofluids: Experimental Investigation.” International Communications in Heat and Mass Transfer 38 (2): 144–48. https://doi.org/DOI 10.1016/j.icheatmasstransfer.2010.11.019
  13. Hwang, Y, J K Lee, J K Lee, Y M Jeong, S I Cheong, Y C Ahn, and S H Kim. 2008. “Production and Dispersion Stability of Nanoparticles in Nanofluids.” Powder Technology 186 (2): 145–53. https://doi.org/DOI 10.1016/j.powtec.2007.11.020
  14. Imura, H, H Kusada, J Oyata, T Miyazaki, and N Sakamoto. 1977. “Heat Transfer in Two-Phase Closed-Type Thermosyphons.” Transactions of Japan Society of Mechanical Engineers 22: 485–493
  15. Jengsooksawat, S, K Booddachan, and S Rittidech. 2014. “Loop Thermosyphon with Vapour Chamber : A Thermodynamic Study.” Advances in Mechanical Engineering 6: 1–8. https://doi.org/10.1155/2014/487191
  16. Jengsooksawat, S, S Pimpru, K Booddachan, and S Rittidech. 2008. “Heat Transfer Characteristic of Loop Thermosyphon with Vapor Chamber.” The 9th International Heat Pipe Symposium. Malaysia
  17. Jiao, B, L M Qiu, X B Zhang, and Y Zhang. 2008. “Investigation on the Effect of Filling Ratio on the Steady-State Heat Transfer Performance of a Vertical Two-Phase Closed Thermosyphon.” Applied Thermal Engineering 28: 1417–26. https://doi.org/10.1016/j.applthermaleng.2007.09.009
  18. Kang, S W, W C Wei, S H Tsai, and C C Huang. 2009. “Experimental Investigation of Nanofluids on Sintered Heat Pipe Thermal Performance.” Applied Thermal Engineering 29 (5–6): 973–79. https://doi.org/10.1016/j.applthermaleng.2008.05.010
  19. Khandekar, S, Y M Joshi, and B Mehta. 2008. “Thermal Performance of Closed Two-Phase Thermosyphon Using Nanofluids.” Thermal Science 47: 667–95. https://doi.org/10.1016/j.ijthermalsci.2007.06.005
  20. Khazaee, I, R Hosseini, A Kianifar, and S H Noie. 2011. “Experimental Consideration and Correlation of Heat Transfer of a Two-Phase Closed Thermosyphon Due to the Inclination Angle, Filling Ratio, and Aspect Ratio.” Journal of Enhanced Heat Transfer 18 (1): 31–40. DOI: 10.1615/JEnhHeatTransf.v18.i1.30
  21. Khodabandeh, R, and R Furberg. 2010. “Heat Transfer, Flow Regime and Instability of a Nano- and Micro-Porous Structure Evaporator in a Two-Phase Thermosyphon Loop.” International Journal of Thermal Sciences 49 (7): 1183–92. https://doi.org/10.1016/j.ijthermalsci.2010.01.016
  22. Kwak, K, and C Kim. 2005. “Viscosity and Thermal Conductivity of Copper Oxide Nanofluid Dispersed in Ethylene Glycol.” Korea-Australia Rheology Journal 17 (2): 35–40
  23. Lee, J S, S H Rhi, C N Kim, and Y Lee. 2003. “Use of Two-Phase Loop Thermosyphons for Thermoelectric Refrigeration: Experiment and Analysis.” Applied Thermal Engineering 23 (9): 1167–76. https://doi.org/Doi 10.1016/S1359-4311(03)00043-7
  24. Li, X.F., D.S. Zhu, X.J. Wang, N. Wang, J.W. Gao, and H. Li. 2008. “Thermal Conductivity Enhancement Dependent PH and Chemical Surfactant for Cu-H2O Nanofluids.” Thermochimica Acta 469 (1–2): 98–103. https://doi.org/10.1016/j.tca.2008.01.008
  25. Li, Z H. 2002. “Modeling and Optimization for Heat Exchanger Networks Synthesis Based on Expert System and Genetic Algorithm.” Chinese Journal of Chemical Engineering 10 (3): 290–97
  26. Lin, Y H, S W Kang, and H L Chen. 2008. “Effect of Silver Nano-Fluid on Pulsating Heat Pipe Thermal Performance.” Applied Thermal Engineering 28: 1312–17. https://doi.org/10.1016/j.applthermaleng.2007.10.019
  27. Lock, G S H. 1992. The Tubular Thermosyphon Variations on a Theme. Edited by 1st. New York: United State: Oxford University Press
  28. Musmar, S A, A T Al-Halhouli, I Tlili, and S Buttgenbach. 2016. “Performance Analysis of a New Water-Based Microcooling System.” Experimental Heat Transfer 29 (4): 485–99. https://doi.org/10.1080/08916152.2015.1024353
  29. Noie-Baghban, S H. 2005. “Heat Transfer Characteristics of a Two Phase Closed Thermosyphon.” Applied Thermal Engineering 25: 495–506. https://doi.org/10.1016/j.applthermaleng.2004.06.019
  30. Noie Zeinali Heris, S., Kahani, M. and Nowee, S.M., S H. 2009. “Heat Transfer Enhancement Using Al2O3/Water Nanofluid in a Two-Phase Closed Thermosyphon.” Heat and Fluid Flow 30 (4): 700–705. https://doi.org/10.1016/j.ijheatfluidflow.2009.03.001
  31. Noie, S. H., M. R. Sarmasti Emami, and M. Khoshnoodi. 2007. “Effect of Inclination Angle and Filling Ratio on Thermal Performance of a Two-Phase Closed Thermosyphon under Normal Operating Conditions.” Heat Transfer Engineering 28 (4): 365–71. https://doi.org/10.1080/01457630601122997
  32. O’Hanley, Harry, Jacopo Buongiorno, Thomas McKrell, and Lin Wen Hu. 2012. “Measurement and Model Validation of Nanofluid Specific Heat Capacity with Differential Scanning Calorimetry.” Advances in Mechanical Engineering. https://doi.org/10.1155/2012/181079
  33. Paramatthanuwat, T, S Boothaisong, S Rittidech, and K Booddachan. 2010. “Heat Transfer Characteristics of a Two-Phase Closed Thermosyphon Using de Ionized Water Mixed with Silver Nano.” Heat and Mass Transfer 46 (3): 281–85. https://doi.org/DOI 10.1007/s00231-009-0565-y
  34. Parametthanuwat Bhuwakietkumjohn, N., Rittidech, S. and Ding, Y., T. 2015. “Experimental Investigation on Thermal Properties of Silver Nanofluids.” Heat and Fluid Flow 56: 80–90. https://doi.org/10.1016/j.ijheatfluidflow.2015.07.005
  35. Parametthanuwat, T., N. Bhuwakietkumjohn, S. Rittidech, and Y. Ding. 2015. “Experimental Investigation on Thermal Properties of Silver Nanofluids.” International Journal of Heat and Fluid Flow 56: 80–90. https://doi.org/10.1016/j.ijheatfluidflow.2015.07.005
  36. Parametthanuwat, T., S. Rittidech, and A. Pattiya. 2010. “A Correlation to Predict Heat-Transfer Rates of a Two-Phase Closed Thermosyphon (TPCT) Using Silver Nanofluid at Normal Operating Conditions.” International Journal of Heat and Mass Transfer 53 (21–22): 4960–65. https://doi.org/10.1016/j.ijheatmasstransfer.2010.05.046
  37. Parametthanuwat, T, and S Rittidech. 2012. “Heat Transfer Characteristics of the Two-Phase Closed Thermosyphon (TPCT) Containing Silver Nanofluids with Oleic Acid Surfactant.” Mechanical Engineering. Mahasarakham; Thailand: Mahasarakham University
  38. Parametthanuwat, Thanya, Sampan Rittidech, Adisak Pattiya, Yulong Ding, and Sanjeeva Witharana. 2011. “Application of Silver Nanofluid Containing Oleic Acid Surfactant in a Thermosyphon Economizer.” Nanoscale Research Letters 6 (1): 315. https://doi.org/10.1186/1556-276X-6-315
  39. Patel, H E, S K Das, T Sundararajan, A Sreekumaran Nair, B George, and T Pradeep. 2003. “Thermal Conductivities of Naked and Monolayer Protected Metal Nanoparticle Based Nanofluids: Manifestation of Anomalous Enhancement and Chemical Effects.” Applied Physics Letters 83 (14): 2931–33. https://doi.org/10.1063/1.1602578
  40. Payakaruk, T, P Terdtoon, and S Ritthidech. 2000. “Correlations to Predict Heat Transfer Characteristics of an Inclined Closed Two-Phase Thermosyphon at Normal Operating Conditions.” Applied Thermal Engineering 20 (9): 781–90. https://doi.org/10.1016/s1359-4311(99)00047-2
  41. Qi, Y, Y Kawaguchi, and Z Lin. 2001. “Enhanced Heat Transfer of Drag Reducing Surfactant Solutions with Fluted Tube-in-Tube Heat Exchanger.” Int J Heat Mass Transf 44: 1495–1505. https://doi.org/10.1016/S0017-9310(00)00203-9
  42. Radiom, Milad, Chun Yang, and Weng Kong Chan. 2013. “Dynamic Contact Angle of Water-Based Titanium Oxide Nanofluid.” Nanoscale Research Letters. https://doi.org/10.1186/1556-276X-8-282
  43. Rahimi, M, K Asgary, and S Jesri. 2010. “Thermal Characteristics of a Resurfaced Condenser and Evaporator Closed Two-Phase Thermosyphon.” International Communications in Heat and Mass Transfer 37 (6): 703–10. https://doi.org/10.1016/j.icheatmasstransfer.2010.02.006
  44. Ramesh, Gopalan, and Narayan Kotekar Prabhu. 2011. “Review of Thermo-Physical Properties, Wetting and Heat Transfer Characteristics of Nanofluids and Their Applicability in Industrial Quench Heat Treatment.” Nanoscale Research Letters 6. https://doi.org/33410.1186/1556-276x-6-334
  45. Reay, D, and P Kew. 2006. Heat Pipe, Theory, Design And Application. Fifth edit. Butterworth-Heinemann
  46. Ristoiu, D, T Ristoiu, C Coama, and D Cenan. 2003. “Experimental Investigation of Inclination Angle on Heat Transfer Characteristics of Closed Two-Phase Thermosyphon.” In 5th General Conference of the Balkan Physical
  47. Rittidech, S, N Pipatpaiboon, and P Terdtoon. 2007. “Heat-Transfer Characteristics of a Closed-Loop Oscillating Heat-Pipe with Check Valves.” Applied Energy 84 (5): 565–77. https://doi.org/DOI 10.1016/j.apenergy.2006.09.010
  48. Rittidech, S, and S Sangiamsuk. 2012. “Internal Flow Patterns on Heat Transfer Performance of a Closed-Loop Oscillating Heat Pipe with Check Valves.” Experimental Heat Transfer 25 (1): 48–57. https://doi.org/Doi 10.1080/08916152.2011.559568
  49. S.J Kim J.Buongiorno, L.W.Hu, I.C.Bang. 2007. “Study of Pool Boiling and Critical Heat Flux Enhancement in Nanofluids.” Bull.Pol.Ac:Tech. 55 (2): 211–16
  50. Sharma, P, I H Baek, T Cho, S Park, and K B Lee. 2011. “Enhancement of Thermal Conductivity of Ethylene Glycol Based Silver Nanofluids.” Powder Technology 208 (1): 7–19. https://doi.org/DOI 10.1016/j.powtec.2010.11.016
  51. Srimuang, W, S Rittidech, and B Bubphachot. 2009. “Heat Transfer Characteristics of a Vertical Flat Thermosyphon (VFT).” Journal of Mechanical Science and Technology 23 (9): 2548–54. https://doi.org/10.1007/s12206-009-0703-y
  52. Terdtoon, P, M Chailungkar, and M Shiraishi. 1998. “Effects of Aspect Ratios on Internal Flow Patterns of an Inclined Closed Two-Phase Thermosyphon at Normal Operating Condition.” Heat Transfer Engineering 19 (4): 75–85. https://doi.org/10.1080/01457639808939938
  53. Vincent, Charles C.J., and Jim B.W. Kok. 1992. “Investigation of the Overall Transient Performance of the Industrial Two-Phase Closed Loop Thermosyphon.” International Journal of Heat and Mass Transfer. https://doi.org/10.1016/0017-9310(92)90033-O
  54. Warrier, P, and A Teja. 2011. “Effect of Particle Size on the Thermal Conductivity of Nanofluids Containing Metallic Nanoparticles.” Nanoscale Research Letters 6. https://doi.org/Artn 247Doi 10.1186/1556-276x-6-247
  55. Yu, W, France D.M., Choi S.U.S., and J L Rooutbort. 2007. “Review and Assessment of Nanofluids Technology for Transportation and Other Application, Energy System Division,.” Argonne National, Argonne, IL60439, USA., April
  56. Zamzamian, Amirhossein, Shahin Nasseri Oskouie, Ahmad Doosthoseini, Aliakbar Joneidi, and Mohammad Pazouki. 2011. “Experimental Investigation of Forced Convective Heat Transfer Coefficient in Nanofluids of Al2O3/EG and CuO/EG in a Double Pipe and Plate Heat Exchangers under Turbulent Flow.” Experimental Thermal and Fluid Science 35 (3): 495–502. https://doi.org/https://doi.org/10.1016/j.expthermflusci.2010.11.013

Last update:

No citation recorded.

Last update: 2024-03-26 14:31:05

No citation recorded.