DOI: https://doi.org/10.14710/ijred.2023.50462

Design and Optimization of a Rack and Pinion Type WEC Using an Auxiliary Vibrating System

School of Information Technology, Engineering, Mathematics and Physics (STEMP), The University of the South Pacific, Suva, Fiji

Received: 23 Oct 2022; Revised: 26 Dec 2022; Accepted: 8 Jan 2023; Available online: 18 Jan 2023; Published: 15 Mar 2023.
Editor(s): H Hadiyanto
Open Access Copyright (c) 2023 The Author(s). Published by Centre of Biomass and Renewable Energy (CBIORE)
Creative Commons License This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Citation Format:
Abstract

Research on wave energy converters with Rack and pinion type Power Take-Off (PTO) has been increasing over the last few years. A few control methods are used to optimize the performance of the said Wave Energy Converters (WECs). This paper presents a novel auxiliary vibrating system that can be implemented to improve the power input to a wave energy converter with a rack and pinion type PTO in regular waves. The design of the WEC system includes a floater, a double rack and pinion arrangement, a vibrating system, and a Mechanical Motion Rectifier (MMR) consisting of two one-way bearings that can convert the bidirectional wave motion to a unidirectional rotation of the output shaft. Once the waves move the floater upwards, this compresses the vibrating system which absorbs some of the energy and then the vibrating system helps the floater return to its original position by releasing the stored energy. The vibrating system also serves as a control method for limiting rack movement, so the impact of the waves is not detrimental to the system. This article aims to approximate the optimized power input to the system and investigate whether the implementation of a novel vibrating system improves the system power input. Allowing the WEC’s natural frequency to reach the wave’s natural frequency is important as it allows for maximum power absorption. The use of vibration systems to tune the WEC’s natural frequency close to the waves’ is novel and serves as the main factor in choosing this research. The WEC was modeled as 2 spring mass damper systems. Then the characteristic equations of the systems were extracted from the equations of motion and solved analytically to obtain the responses. One-factor-at-a-time (OFAT) method together with two different algorithms (Genetic and Multi-Start algorithms) from MATLAB code were used to optimize the response. The optimized power input to the system was then approximated. For system one, the maximum amplitude of the response was seen at a system mass of 500 kg and stiffness in the range of 100<k<240 N/m. The same was achieved for system two at a system mass of 500 kg and stiffness in the range of 100<k<138. The effect of the stiffness and mass on the response and input power has also been discussed. 

Fulltext View|Download
Keywords: Optimization; Wave Energy Convertor; Auxiliary Vibrating System; Rack and Pinion PTO

Article Metrics:

Article Info
Section: Original Research Article
Language : EN
Recent articles
Performance Assessment of Malaysian Fossil Fuel Power Plants: A Data Envelopment Analysis (DEA) Approach Techno-Economic Analysis of Co-firing for Pulverized Coal Boilers Power Plant in Indonesia Wind Speed Prediction Based on Statistical and Deep Learning Models More recent articles
Most cited articles
Ultrasound Assisted Esterification of Rubber Seed Oil for Biodiesel Production A Review of a Successful Unsubsidized Market-Based Rural Solar Development Initiative in Laikipia District, Central Kenya Innovative Green Technology for Sustainable Industrial Estate Development Modeling and Experimental Validation of a Transient Direct Expansion Heat Pump Assessment of Wind Energy Potential in Golestan Province of Iran More cited articles
  1. Aderinto, T., & Li, H. (2018). Ocean Wave Energy Converters: Status and Challenges. Energies, 11(5), 1250–1276. https://doi.org/10.3390/en11051250
  2. Ahamed, R., McKee, K., & Howard, I. (2020). Advancements of wave energy converters based on power take off (PTO) systems: A review. Ocean Engineering, 204, 107248–107273. https://doi.org/10.1016/j.oceaneng.2020.107248
  3. Amin, M. S., Bora Karayaka, H., Yanik, P., & Sang, Y. (2021). Suboptimal Control of a Rack and Pinion Based Wave Energy Converter Power Take-off System. SoutheastCon 2021, 1–7. https://doi.org/10.1109/SoutheastCon45413.2021.9401831
  4. Aminuddin, J., Effendi, M., Nurhayati, N., Widiyani, A., Razi, P., Wihantoro, W., Aziz, A. N., Abdullatif, R. F., Sunardi, S., Bilalodin, B., & Arifin, A. (2020). Numerical Analysis of Energy Converter for Wave Energy Power Generation-Pendulum System. International Journal of Renewable Energy Development, 9(2), 255–261. https://doi.org/10.14710/ijred.9.2.255-261
  5. Bedard, R., & Hagerman, G. (2005). Offshore Wave Power Feasibility Demonstration
  6. Boyle, G. (2004). Renewable Energy: Power for a Sustainable Future (2nd ed.). Oxford University Press
  7. Brooke, J. (2003). Wave Energy Conversion (R. Bhattacharyya & M. McCormick, Eds.; 1st ed., Vol. 6). Elsevier Science
  8. Chandrasekaran, S., & Harender. (2012). Power Generation Using Mechanical Wave Energy Converter. The International Journal of Ocean and Climate Systems, 3(1), 57–70. https://doi.org/10.1260/1759-3131.3.1.57
  9. Czech, B., & Bauer, P. (2012). Wave Energy Converter Concepts : Design Challenges and Classification. IEEE Industrial Electronics Magazine, 6(2), 4–16. https://doi.org/10.1109/MIE.2012.2193290
  10. Dang, T. D., Phan, C. B., & Ahn, K. K. (2019). Design and Investigation of a Novel Point Absorber on Performance Optimization Mechanism for Wave Energy Converter in Heave Mode. International Journal of Precision Engineering and Manufacturing-Green Technology, 6(3), 477–488. https://doi.org/10.1007/s40684-019-00065-w
  11. Do, T. C., Dang, T. D., & Ahn, K. K. (2022). Efficiency Improvement of a Hydraulic Power Take-off of Wave Energy Converter Using Variable Displacement Motor. International Journal of Precision Engineering and Manufacturing-Green Technology, 9(4), 1087–1099. https://doi.org/10.1007/s40684-021-00371-2
  12. Drew, B., Plummer, A. R., & Sahinkaya, M. N. (2009). A review of wave energy converter technology. Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, 223(8), 887–902. https://doi.org/10.1243/09576509JPE782
  13. EMEC. (2014). PELAMIS WAVE POWER. The Eurpoean Marine Energy Centre LTD. https:/www.emec.org.uk/about-us/wave-clients/pelamis-wave-power/
  14. Faizal, M., Ahmed, M. R., & Lee, Y.-H. (2014). A Design Outline for Floating Point Absorber Wave Energy Converters. Advances in Mechanical Engineering, 6, 846097. https://doi.org/10.1155/2014/846097
  15. Falcão, A. F. de O. (2010). Wave energy utilization: A review of the technologies. Renewable and Sustainable Energy Reviews, 14(3), 899–918. https://doi.org/10.1016/j.rser.2009.11.003
  16. Falnes, J. (2007). A review of wave-energy extraction. Marine Structures, 20(4), 185–201. https://doi.org/10.1016/j.marstruc.2007.09.001
  17. Gunn, K., & Stock-Williams, C. (2012). Quantifying the global wave power resource. Renewable Energy, 44, 296–304. https://doi.org/10.1016/j.renene.2012.01.101
  18. Hadano, K., Lee, K. Y., & Moon, B. Y. (2017). Wave energy conversion utilizing vertical motion of water in the array of water chambers aligned in the direction of wave propagation. International Journal of Naval Architecture and Ocean Engineering, 9(3), 239–245. https://doi.org/10.1016/j.ijnaoe.2016.06.002
  19. Henderson, R. (2006). Design, simulation, and testing of a novel hydraulic power take-off system for the Pelamis wave energy converter. Renewable Energy, 31(2), 271–283. https://doi.org/10.1016/j.renene.2005.08.021
  20. Hooke, R., & Jeeves, T. A. (1961). ``Direct Search’’ Solution of Numerical and Statistical Problems. Journal of the ACM, 8(2), 212–229. https://doi.org/10.1145/321062.321069
  21. Immanuel, S. D., & Chakraborty, U. Kr. (2019). Genetic Algorithm: An Approach on Optimization. 2019 International Conference on Communication and Electronics Systems (ICCES), 701–708. https://doi.org/10.1109/ICCES45898.2019.9002372
  22. Jahangir, M. H., & Ghanbari Motlagh, S. (2022). Feasibility study of CETO wave energy converter in Iranian coastal areas to meet electrical demands (a case study). Energy for Sustainable Development, 70, 272–289. https://doi.org/10.1016/j.esd.2022.07.017
  23. Jiang, Y., Peng, Y., Sun, Y., Zong, Z., & Sun, L. (2021). Design and Testing of a Mechanical Power Take-off System for Rolling-type Wave Energy Converter. International Journal of Precision Engineering and Manufacturing-Green Technology, 8(5), 1487–1499. https://doi.org/10.1007/s40684-020-00253-z
  24. Kim, J., & Cho, I.-H. (2021). Wave power extraction by multiple wave energy converters arrayed in a water channel resonator. International Journal of Naval Architecture and Ocean Engineering, 13, 178–186. https://doi.org/10.1016/j.ijnaoe.2021.02.004
  25. Kofoed, J. P., Frigaard, P., Friis-Madsen, E., & Sørensen, H. Chr. (2006). Prototype testing of the wave energy converter wave dragon. Renewable Energy, 31(2), 181–189. https://doi.org/10.1016/j.renene.2005.09.005
  26. Kolda, T. G., Lewis, R. M., & Torczon, V. (2003). Optimization by Direct Search: New Perspectives on Some Classical and Modern Methods. SIAM Review, 45(3), 385–482. https://doi.org/10.1137/S003614450242889
  27. Liang, C., Ai, J., & Zuo, L. (2017). Design, fabrication, simulation and testing of an ocean wave energy converter with mechanical motion rectifier. Ocean Engineering, 136, 190–200. https://doi.org/10.1016/j.oceaneng.2017.03.024
  28. MATLAB. (2010). How GlobalSearch and MultiStart Work. MathWorks. https://au.mathworks.com/help/gads/how-globalsearch-and-multistart-work.html
  29. Monteiro, L., Sarmento, A., & Madaleno, W. (2019). Analysing the Possibility of Extracting Energy from Ocean Waves in Cabo-Verde to Produce Clean Electricity - Case-Study: the Leeward Islands. International Journal of Renewable Energy Development, 8(1), 103. https://doi.org/10.14710/ijred.8.1.103-112
  30. OPT. (2008). PB3 PowerBuoy. Ocean Power Technology. https://oceanpowertechnologies.com/platform/opt-pb3-powerbuoy/
  31. Polinder, H., & Scuotto, M. (2005). Wave energy converters and their impact on power systems. 2005 International Conference on Future Power Systems, 1–9. https://doi.org/10.1109/FPS.2005.204210
  32. Rahm, M., Boström, C., Svensson, O., Grabbe, M., Bülow, F., & Leijon, M. (2010). Offshore underwater substation for wave energy converter arrays. IET Renewable Power Generation, 4(6), 602–612. https://doi.org/10.1049/iet-rpg.2009.0180
  33. Ram, K., Narayan, S., Ahmed, M. R., Nakavulevu, P., & Lee, Y. H. (2014). In situ near-shore wave resource assessment in the Fiji Islands. Energy for Sustainable Development, 23, 170–178. https://doi.org/10.1016/j.esd.2014.09.002
  34. Setyandito, O., Nizam, N., Pierre, A. J., Putra, G. D., Wijayanti, Y., & Anda, M. (2022). Numerical Analysis of Velocity Magnitude on Wave Energy Converter System in Perforated Breakwater. International Journal of Renewable Energy Development, 11(1), 27–33. https://doi.org/10.14710/ijred.2022.38535
  35. Tri, N. M., Binh, P. C., & Ahn, K. K. (2018). Power take-off system based on continuously variable transmission configuration for wave energy converter. International Journal of Precision Engineering and Manufacturing-Green Technology, 5(1), 89–101. https://doi.org/10.1007/s40684-018-0010-0
  36. Wacher, A., & Neilsen, K. (2010). Mathematical and Numerical Modeling of the AquaBuOY Wave Energy Converter. Industry Case Studies Journal, 2, 16–33
  37. Wave Dragon. (2011). The Wave Dragon Technology. Wave Dragon ApS. http://wavedragon.net/
  38. Weber, J., Mouwen, F., Parish, A., & Robertson, D. (2009). Wavebob – Research & Development Network and Tools in the Context of Systems Engineering. 8th European Wave and Tidal Energy Conference (EWTEC 2009), 416–420. http://www.homepages.ed.ac.uk/shs/Wave%20Energy/EWTEC%202009/EWTEC%202009%20(D)/papers/207.pdf
  39. Yang, X.-S. (2013). Optimization and Metaheuristic Algorithms in Engineering. In Metaheuristics in Water, Geotechnical and Transport Engineering (pp. 1–23). Elsevier. https://doi.org/10.1016/B978-0-12-398296-4.00001-5
  40. Youssef, J., Matar, J., Rahme, P., & Bou-Mosleh, C. (2016). A Nearshore Heaving-Buoy Sea Wave Energy Converter for Power Production. Procedia Engineering, 145, 136–143. https://doi.org/10.1016/j.proeng.2016.04.032
  41. Zullah, M. A., Prasad, D., Ahmed, M. R., & Lee, Y.-H. (2010). Performance analysis of a wave energy converter using numerical simulation technique. Science in China Series E: Technological Sciences, 53(1), 13–18. https://doi.org/10.1007/s11431-010-0026-3

Last update:

No citation recorded.

Last update: 2024-11-24 07:25:18

No citation recorded.