1Department of Chemical Engineering, Syiah Kuala University, Banda Aceh, Indonesia
2Department of Chemical Science and Engineering, Kobe University, Kobe, Japan
BibTex Citation Data :
@article{JKSA66681, author = {Anisa Luthfiana and Sri Mulyati and Nasrul Arahman and Aulia Cintia Ambarita and Muhammad Aulia}, title = {Cigarette Filter-Based Membranes with Tannin and FeCl₃ Additives for Enhancing the Antifouling Properties of Oil Emulsion Filtration}, journal = {Jurnal Kimia Sains dan Aplikasi}, volume = {27}, number = {12}, year = {2024}, keywords = {Cigarette filter membranes; Tannic acid and FeCl3 modification; Antifouling properties; Oil emulsion separation}, abstract = { Industries in Indonesia significantly contribute to the economy by increasing foreign exchange earnings and creating job opportunities. However, industrial activities also negatively impact the environment, particularly water pollution caused by liquid waste containing oil emulsions. This research aims to develop a membrane based on cigarette filters as an alternative to cellulose acetate for separating oil emulsions in water. Cigarette filters were processed into membranes with tannic acid (TA) and ferric chloride (FeCl 3 ) as additives using a vacuum-filtration coating technique. The resulting membranes were tested for their characteristics and performance, including morphological analysis, functional group analysis, hydrophilicity, water uptake, porosity, pure water flux, selectivity toward oil emulsions (artificial emulsions from CPO and sodium dodecyl sulfate (SDS)) and antifouling properties. The results showed that membranes with additives exhibited more uniform pores, asymmetric structures, and improved surface characteristics. The addition of tannic acid 2.4 mmol and FeCl 3 3.7 mmol also enhanced the antifouling properties of the membranes, although it decreased the pure water flux. Membranes without additives (M1) and with additives (M2) were compared for pure water flux, separation efficiency, and antifouling properties. M2 exhibited a lower flux (15.03 L/m 2 ·h) than M1 (19.69 L/m 2 ·h) due to reduced porosity. Although the oil emulsion selectivity of M2 (97.80%) showed no significant improvement compared to M1 (97.79%), the addition of additives notably enhanced the antifouling performance. M2 demonstrated a flux recovery ratio (FRR) of 71.22%, significantly higher than M1’s FRR of 46.01%, indicating the effectiveness of the additives in reducing fouling and improving membrane reusability. The membranes achieved high selectivity for oil emulsions with a separation efficiency of up to 97%. These findings suggest that using cigarette filters as the base material for membranes and adding additives can provide an efficient and environmentally friendly solution to reducing oil emulsion pollution. }, issn = {2597-9914}, pages = {580--589} doi = {10.14710/jksa.27.12.580-589}, url = {https://ejournal.undip.ac.id/index.php/ksa/article/view/66681} }
Refworks Citation Data :
Industries in Indonesia significantly contribute to the economy by increasing foreign exchange earnings and creating job opportunities. However, industrial activities also negatively impact the environment, particularly water pollution caused by liquid waste containing oil emulsions. This research aims to develop a membrane based on cigarette filters as an alternative to cellulose acetate for separating oil emulsions in water. Cigarette filters were processed into membranes with tannic acid (TA) and ferric chloride (FeCl3) as additives using a vacuum-filtration coating technique. The resulting membranes were tested for their characteristics and performance, including morphological analysis, functional group analysis, hydrophilicity, water uptake, porosity, pure water flux, selectivity toward oil emulsions (artificial emulsions from CPO and sodium dodecyl sulfate (SDS)) and antifouling properties. The results showed that membranes with additives exhibited more uniform pores, asymmetric structures, and improved surface characteristics. The addition of tannic acid 2.4 mmol and FeCl3 3.7 mmol also enhanced the antifouling properties of the membranes, although it decreased the pure water flux. Membranes without additives (M1) and with additives (M2) were compared for pure water flux, separation efficiency, and antifouling properties. M2 exhibited a lower flux (15.03 L/m2·h) than M1 (19.69 L/m2·h) due to reduced porosity. Although the oil emulsion selectivity of M2 (97.80%) showed no significant improvement compared to M1 (97.79%), the addition of additives notably enhanced the antifouling performance. M2 demonstrated a flux recovery ratio (FRR) of 71.22%, significantly higher than M1’s FRR of 46.01%, indicating the effectiveness of the additives in reducing fouling and improving membrane reusability. The membranes achieved high selectivity for oil emulsions with a separation efficiency of up to 97%. These findings suggest that using cigarette filters as the base material for membranes and adding additives can provide an efficient and environmentally friendly solution to reducing oil emulsion pollution.
Article Metrics:
Last update:
Last update: 2025-01-21 11:38:24
As an article writer, the author has the right to use their articles for various purposes, including use by institutions that employ authors or institutions that provide funding for research. Author rights are granted without special permission.
Author who publishes a paper at JKSA has the broad right to use their work for teaching and scientific purposes without the need to ask permission, including: used for (i) teaching in the author's class or institution, (ii) presentation at meetings or conferences and distributing copies to participants ; (iii) training conducted by the author or author's institution; (iv) distribution to colleagues for research use; (v) use in the compilation of subsequent authors' works; (vi) inclusion in a thesis or dissertation; (vi) reuse of part of the article in another work (with citation); (vii) preparation of derivative works (with citation); (viii) voluntary posting on open websites operated by authors or author institutions for scientific purposes (follow the CC BY-SA License).
Authors and readers can copy and redistribute material in any media or format, and mix, modify, and build material for any purpose but they must provide appropriate credit (provide article citation or content), providing links to the license, and indicate if there are changes.
The authors submitting a manuscript do so on the understanding that if accepted for publication, copyright of the article shall be assigned to Jurnal Kimia Sains dan Aplikasi (JKSA). Copyright encompasses rights to reproduce and deliver the article in all form and media, including reprints, photographs, microfilms and any other similar reproductions, as well as translations.
Reproduce any part of this journal, its storage in the database or its transmission by all forms or media is permitted does not need for written permission from JKSA. However, it should be cited as an honor in academic manners
JKSA and the Chemistry Department of Diponegoro University and the Editor make every effort to ensure that there are no data, opinions, or false or misleading statements published in JKSA. However, the content of the article is the sole and exclusive responsibility of each author.
The Copyright Transfer Form can be downloaded here: [Copyright Transfer Form - Indonesian] [Copyright Transfer Form - English]. The copyright form should be signed originally and send to the Editor in the form of printed letters, scanned documents sent via email or fax.
Adi Darmawan, Ph.D (Editor in Chief)
Editor in chief of Jurnal Kimia Sains dan Aplikasi (JKSA)
Chemistry Department, Faculty of Sciences and Mathematics, Diponegoro University
Visitor: View My Stats
Jurnal Kimia Sains dan Aplikasi is indexed in:
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.